• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Recent content by devahoch

  1. can mutoh vj1304 print dye sub

    All prinheads are indentical! do you think EPSON make a water based and solvent based for two technology (technology is very expensive - China can't copy technology / not chinese DX4, DX5..../. Diferent is only manifol for water or solvent. but you can use solvent for water, that not backward.
  2. My self-make roller - Beginning

    Thank you, Pneumatic diagram was done, but I want to make very cheap cost roller, that I don't want to buy a construction from expensive seller. No I made frame for this roller, is very importand linear rail way (and must to be very cheap), I think in 2 week I can show same pictures from project.
  3. Value Jet refillable ink cartridges...confused

    Yes, smartcards are needed. If you want, you can see my post for making a never ending smartcards on mutoh. proces is very cheap and easy, if you need some helps, I am here for you.
  4. My self-make roller - Beginning

    Hello, I go to make roller for my works. I have a old chinese laminator 160cm, I take roll from this. I have 2 air cylinder 80-125 for move roll up-down. I have solenoid for control air presure, Roll move up-down by electric. Want to have a PNEUMATIC-DIAGRAMS for control (If have some one)...
  5. Need Help Falcon Outdoor II not booting

    You have a bad powerboard. If you know to repair, is cc 2 eur, is necessary to replace one or more conductors on this board. If some conductor have a swelling surface, is bad. If you don't know to replate, used powerboadr is cc 100. ..200eur, new is cc 400eur.
  6. Once Again Faulty Chip Readers Causing Errors.

    Thank you, I don't know, that printer recognise depend of card order, I try it. My RH II has firmware 3.00, configuration KYCM MCYK. Configuration 1C1H has nocontanination color per head.
  7. Once Again Faulty Chip Readers Causing Errors.

    Hello Umca! Spitfire 65 have a twin one color per head ? I see two cartridges by the side. From card reader if you cut all RED WIRES and connect together with swicht, Turn ON before start for read cards, after initialize turn OFF you have a never dead cards. Is in my RH II (is 99% same as Spifite)
  8. Need Help Building A Utrasonic Cleanner For Print Head Dx4, Dx5

    Thank you Vander J. Primary i want to soak print head, those heads still in printer and work daily. But my 1. head (black-Yellow) still have a very bad noozle on black channel, Usualy I clean with syringe, but I want to make a big soak with pump abount cc 10, 15 min, that I want to make cleaner...
  9. Need Help Building A Utrasonic Cleanner For Print Head Dx4, Dx5

    Thank you, Now I reading, that ultrasonic cleaner nohelp DX4, DX5 on Printhead recovery. For pump I want to use those things, where I have on hands, I have a defect Controler board for steppers (5 axis and 1 is bad). Stepper motor have a more power than DC motor, I want to make with arduino...
  10. Platen Heater Overheating

    I think, you have a bad heater Relay for thermocouple, This Relay is electric (not electronic) and conntact is still continue, not work when is turn on or off. You need replacing only this, nonecessary to replacing hole board. This is usualy small black plastic box on the board, if you turn on...
  11. Need Help Building A Utrasonic Cleanner For Print Head Dx4, Dx5

    Hi there. I want to build a cleanner for my DX4 heads. For realization I have a pumps from nonused Mutoh RH II, Is completly pumps and tube connects, I want to make PUSH - Pull system for solvent cleaning fluid into heads. I have a question for expert: Utrasonic cleanner is 30-50W 40kHz, this...
  12. IMG_20170325_085107

    IMG_20170325_085107

    Pumps from Mutoh RH II
  13. how to adjust?

    ...As you wrote, prameter is available to adjust for printhead. For all printhead, but not for every cannel. You can see space between Cyan and Magenta. These are two channels of one printhead... I try to see, that is can setting 2 channel on one head, but thit is only way to correct space...
  14. How to make forever smartcards in mutoh - How to

    Principle: every cardreader need 5v for read/write from/to smartcard. For STARD, printer read from smartcard for STATUS of INK. after this, if 5v is turn off, printer time of time sent new status to cardreader, but 5v is off, nothing no-write to smartcard. That smartcard still have a status from...
  15. Mutoh ink useage at rapid rate

    My experiences for stolen ink from cartridge. I have RH II 64. When I maked cleaning then long time no print (cc 2-4 hours), ink spontaneously flows to waste (I missed cc 100ml ink from every of 2 cartridges). I have this 3 time, then I know this. If you make CLEANING, then you must something...
Top