Welcome To Signs101.com: Largest Forum for Signmaking Professionals

Signs101.com: Largest Forum for Signmaking Professionals is the LARGEST online community & discussion forum for professional sign-makers and graphic designers.

 


  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ratings Gino has received

  1. bannertime rated Gino's post Like in the thread Discussion I've owned an HP R1000 since April 2019, ask me anything.

    I have one............ why is there air ??

    Feb 28, 2020 at 11:06 AM
  2. Chuck B rated Gino's post Like in the thread Should have been you ......

    I know just how he feels. I always wanted to be a doctor/surgeon and help fix and cure people, but my parents said I should go into...

    Feb 27, 2020 at 10:50 AM
  3. d fleming rated Gino's post Like in the thread Question Can't find anymore........................

    I tried Grimco and they said they discontinued them recently, as did Glantz and Harbor. I got them at Bulls.

    Feb 25, 2020 at 12:19 PM
  4. wes70 rated Gino's post Like in the thread How should this be handled?.

    While that's a cute analogy, it doesn't quite fit the same scenario as going on here. Someone taking credit for someone else's work is...

    Feb 24, 2020 at 3:11 PM
  5. decalman rated Gino's post Like in the thread 10mm coroplast cut tool?.

    1 or 2 small jobs a month...... invest in a really nice jig saw or scroll saw...... or both. :smile:

    Feb 23, 2020 at 8:28 AM
  6. okeesignguy rated Gino's post Like in the thread Need Help Drawings.

    No cost for a thumbnail drawing, but it doesn't leave the shop. Otherwise, any computerized creation isn't started until a written and...

    Feb 22, 2020 at 8:09 AM
  7. Pixels Are Bad Mmmkay? rated Gino's post Like in the thread Songs stuck in my head.

    Go to around 30 seconds in............. [MEDIA] This'll knock that dumb crap out and stick with you a lot longer.

    Feb 21, 2020
  8. Pixels Are Bad Mmmkay? rated Gino's post Like in the thread 6mm ACM or 5mm AlumaCorr?.

    He said a 1/4" wide by 1" deep notch/groove. For a 4' x 4' sign, I'd use either or. For a 4' x 8', I'd be using 10mm alumalite.

    Feb 21, 2020
  9. Eforcer rated Gino's post Like in the thread Need Help Bubbling Before Printing.

    Looks like cheap stuff and probably not really any good for digital printing, even without the lifting.

    Feb 21, 2020
  10. Evan Gillette rated Gino's post Like in the thread Just found this on my work table.

    You can't fool me.......... that's your handwriting. You just spruced it up a bit to look like your daughter's. Cute :u rock:

    Feb 21, 2020
  11. Texas_Signmaker rated Gino's post Like in the thread Just found this on my work table.

    You can't fool me.......... that's your handwriting. You just spruced it up a bit to look like your daughter's. Cute :u rock:

    Feb 20, 2020
  12. okeesignguy rated Gino's post Like in the thread Question How tough is HDU board?.

    Don't use it all that much, but when we do, it's usually 2" stock. With your situation, I'd definitely back it with 3/4" MDO and make...

    Feb 20, 2020
  13. MHester rated Gino's post Like in the thread 10mm coroplast cut tool?.

    Good jig saw is gonna run ya about $125 to $175. Decent 14" scroll saw about $400 to $600. Have 5 jig saws and one old ******* of a...

    Feb 18, 2020
  14. MHester rated Gino's post Like in the thread 10mm coroplast cut tool?.

    1 or 2 small jobs a month...... invest in a really nice jig saw or scroll saw...... or both. :smile:

    Feb 18, 2020
  15. premiercolour rated Gino's post Like in the thread OH Wholesale Sticker Pricing.

    That is just too funny. It's bad enough they're advertising where they shouldn't be, but that website is atrocious. I'd hate to get...

    Feb 18, 2020
  16. Boudica rated Gino's post Like in the thread Need Help Drawings.

    No cost for a thumbnail drawing, but it doesn't leave the shop. Otherwise, any computerized creation isn't started until a written and...

    Feb 17, 2020
  17. aerial rated Gino's post Like in the thread Substrate choices for post and panel signs.

    Just finished this yesterday. 2" square legs with top & bottom cross pieces (stringers) the same. Welded on 12" x 48" x .080 face...

    Feb 17, 2020
  18. premiercolour rated Gino's post Like in the thread Discussion Does Anyone Realize This.............. ??.

    There are so many threads and mostly POSTS in which members are either replying to help or just plain offering their help to other...

    Feb 15, 2020
  19. Jeremiah rated Gino's post Like in the thread When you outsource, do you tell the customer?.

    It's one thing to be a 'broker' and it's another thing to buy certain things and incorporate them into your work. It's not being...

    Feb 15, 2020
  20. GAC05 rated Gino's post Like in the thread Hanging Sign Material and Bracketing.

    Looking good. Also appears you have the same model camera tex has. That sign is falling over or not level............:wink:

    Feb 14, 2020

 


Loading...