I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
Thanks DYP
This is where my ignorance shows ....
2 Questions please ?
1. What is the difference between a mode and a preset !
2. What is the difference ( if any ), between the phrase "Calibrate" , and "linearize"
I should know a lot more, but as my wife will testify to at home, most...
Thanks for the reply, much appreciated...apologies for the late response, drowning in tedious admin at present !
When we say "each media preset requires its own calibration"
Does that mean each media mode
So if i was printing on my "polyester canvas" media profile
I would need to calibrate for ...
Hi Guys
Trying to get my head around colour / profiling, etc
I should know more, with 5x Latex machines, but it used to go on around me, as opposed to with me, historically.
Linearise / Calibrate
Is this independent of the media / ICC ?
When you calibrate or linearize a Printer, is this just...
Thank you very much
I went back to my warehouse
Cleaned the strip
Cleaned and lunricated the rail
And popped a few prints on
Fingers crossed
Will see in the morning
Thank you
Thanks Balststrat, i will do that 1st thing in the morning.
Were the symptoms i showed a common issue if the encoder strip is dirty ?
I wondered if it was because i had cut prints mid roll, but i do that all the time and am always careful not to apply pressure to the roll
Any other things to...
Hi Guys,
Hope you can help or offer some advice please
A couple of times today, and once during the week, we had the print almost swerve off its path
Our prints have an equal gutter on each side of the print
The roll remains straight, it is not unwound uneven, but for some reason the print...
Pardon my ignorance ! i presume those are those coloured bars that i sometimes see either side of proofs ( i know i should know more , as ive been involved 15+ years, but largely not hands on ) . How do i get these spit bars on prints if needed ? ( i use Onyx ) . Appreciate the answer, even if...
ive bought a 2nd hand i1pro 2 and an i1io table, so i need to start learning about colour, which is something i know very little about. But i couldnt bear the throught of manually scanning those patches, so invedted in the semi automated tool. Anyone had any experience with the i1io robotic arm...
Hi Guys,
Thanks for all of your replies
Hi Balstestrat,
Thanks for the info, much appreciated.
I have a very old EFI ES-1000 hand held profiler
I have no idea if drivers / software are still available for this ?
My colleague used to use it , way back in the day when we sold print media
I...
Hi Guys
Hope you can give a little advice please.
We should know more about printing that we do, but are pretty one dimensional, printing just canvas, across 5 Latex 315 machines
And have done for years
Our issue is that we really struggle to get consistent colours across the 5 machines. In...
Thanks BALLPARK
Thanks also dypinc
On the subject of which RIPs support this.....@dypinc ....do you know if Onyx Postershop supports this feature for the 3xx series ?
Also on the subject of RIPs.....my version of Onyx Postershop , which currently supports 3 machines....is from mid 2013...
Hi,
thanks for taking the time to reply, much appreciated
I noticed in a different thread, that there was a firmware update in Sept 2016, that looked like it allowed for continuous printing now ?
HP 300 Series Firmware NEXUS_01_10_00.4 - Released 9/14/16
An update for the 300 series, on...
Hi,
Hope you could clarify a point for me please.
I am considering a new Latex machine.
My question regards 365 Latex
Does the 365 do "continuous printing" ?
Or does it do that annoying drying cycle between prints ?
We have an older latex machibe that takes a long time on individual prints...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.