• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Recent content by Netter26

  1. Firmware Update Nozzle Check

    I installed the v3.09 firmware update on my VJ1324, and now my Nozzle Checks are different. The nozzle check prints the date, time and version along with one block of black, zero blocks of cyan and two blocks of yellow and magenta like normal. The Nozzle checks were perfect before the update and...
  2. Mutoh 1324 new Maintenance Station noise

    Thanks, it is a third party MS but is working. I’ll try greasing the gears. I also have a cross contamination issue. My first yellow block on the nozzle check is kind of green. I have new dampers in but not new O rings. Also the blue and yellow on the nozzle check is only spitting out 9 of the...
  3. Mutoh 1324 new Maintenance Station noise

    Hello, I just installed a new Maintenance Station on my VJ 1324 and it’s making a loud noise when cleaning. Usually when it’s sucking the ink down the cap top once the printhead moves off of it. When I do a little charge, it makes the noise while the head is on the cap top. It’s the sound it...
  4. Reuse Mutoh Ink Cartridge

    thank you!
  5. Reuse Mutoh Ink Cartridge

    Hi, I purchased a third party ink for my Mutoh VJ1324 that I received without a chip card applied to it. I plugged it in not realizing it. If I purchase a card, can I use it if it has sat for a month with the hole punctured on it? Thanks
  6. Reuse Ink Cartridge that has previously been plugged in

    Hi, I purchased a third party ink that I received without a chip card applied to it. I plugged it in not realizing it. If I purchase a card, can I use it if it has sat for a month with the hole punctured on it? Thanks
  7. Random lines while printing

    Has anybody seen this happen before? It just started randomly dropping these lines every few passes. I’m using a Mutoh VJ1324. Not sure what the problem is.
  8. VJ1324 Random lines every few inches

    My JV1324 is printing a strip of vertical lines every couple inches. My nozzle check is almost perfect. Could this be an electrical issue?
  9. VJ1324 Media Not Pulling

    Would anybody know why or what I need to fix when my VJ1324 doesn't pull full 50 yard rolls very well. I have to roll out as much as I can and babysit the printer while printing. Otherwise it will lay the ink down too thick or kind of give a faded look in the print. Thank you
  10. Mark on Prints

    Nice! Great idea. That makes sense to why that mark would show up. Thank you
  11. Mark on Prints

    Okay thanks, I’ll check that out. Could be from the table from loading up the roll. my nozzle check is perfect and I’ve cleaned the encoder strip within the last 3 days. The encoder strip has some small scratches on it from the back and forth motion, could that cause an issue?
  12. Mark on Prints

    I have a VJ1324 and I’ve been getting what looks like a static mark on all my prints. It happens the left side of the printer 3/4 the way down, then the mark angles upwards until it reaches the end of the vinyl on the left side. Always happens in the same spot and pattern. I have the printer...
  13. Nozzle check missing yellow

    Okay, I have 4 new dampers so I’ll probably just change them all and see if that helps. Thank you.
  14. Nozzle check missing yellow

    I have a Mutoh 1324 and recently I’ve lost a whole yellow channel. Nozzle check is near perfect except for the one whole block of yellow on the left. The right block of yellow is perfect. I installed a new maintenance station in August. Any ideas? Thank you.
  15. Need Help Arlon 3420 Laminate buckling

    Thanks, I think you're about it being a humidity issue. I've ran the dehumidifier a couple days and has seemed to help it release better.
Top