Welcome To Signs101.com: Largest Forum for Signmaking Professionals

Signs101.com: Largest Forum for Signmaking Professionals is the LARGEST online community & discussion forum for professional sign-makers and graphic designers.

 


  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ratings OhioSigns has received

  1. signage rated OhioSigns's post Like in the thread Brushed aluminum ACM outdoors?.

    When I was looking at Brushed Aluminum ACM awhile back most of the stuff offered by sign suppliers was for interior use only. I have a...

    May 11, 2020
  2. PrintGod31 rated OhioSigns's post Like in the thread NEED TO KNOW.

    Magnets whenever possible...... for tape I use the blue 1" Duck Clean Release painters tape. Generally has enough hold and doesn't leave...

    Apr 15, 2020
  3. Jburns rated OhioSigns's post Like in the thread Floor Graphics.

    I use 3M 40C vinyl with 3M 3645 overlaminate and they hold up great to normal foot traffic. They are easy to install and remove. A local...

    Apr 15, 2020
  4. Kali539 rated OhioSigns's post Like in the thread Suggestions Have a need for some ideas................................

    Could you do a banner with pole pockets top and bottom and then use ratchet straps that would wrap around the trailer and either attach...

    Jan 15, 2020
  5. joshGN rated OhioSigns's post Like in the thread Suggestions Have a need for some ideas................................

    Could you do a banner with pole pockets top and bottom and then use ratchet straps that would wrap around the trailer and either attach...

    Jan 15, 2020
  6. Gino rated OhioSigns's post Like in the thread Suggestions Have a need for some ideas................................

    Could you do a banner with pole pockets top and bottom and then use ratchet straps that would wrap around the trailer and either attach...

    Jan 14, 2020
  7. Mascitti Bro rated OhioSigns's post Like in the thread Apply Vinyl to Wrapped Car.

    The main concern would be ghosting if they remove the graphics from the wrap down the road. The graphics will preserve the color under...

    Jan 13, 2020
  8. Dave Byrne rated OhioSigns's post Like in the thread Corrugated panel widths.

    If you have the corrugated metal to measure just run a piece of tape down it going into the valleys. Mark / cut the ends then lay it out...

    Jun 25, 2019
  9. spectrum maine rated OhioSigns's post Like in the thread Corrugated panel widths.

    If you have the corrugated metal to measure just run a piece of tape down it going into the valleys. Mark / cut the ends then lay it out...

    Jun 25, 2019
  10. studio 440 rated OhioSigns's post Like in the thread Corrugated panel widths.

    If you have the corrugated metal to measure just run a piece of tape down it going into the valleys. Mark / cut the ends then lay it out...

    Jun 25, 2019
  11. the east coast kid rated OhioSigns's post Like in the thread Question Has anyone tried double laminating prints for better protection? Needing solution to protect wrap..

    Is there mud flaps on the front wheels or does he have wheels on it that stick out past the body that might be flipping up rocks?

    Jun 7, 2019
  12. Mascitti Bro rated OhioSigns's post Like in the thread Can we talk "Race Car" graphics?.

    schoolofracinggraphics.com

    Apr 22, 2019
  13. Steven 54 rated OhioSigns's post Like in the thread Can we talk "Race Car" graphics?.

    schoolofracinggraphics.com

    Apr 20, 2019
  14. dsd7 rated OhioSigns's post Like in the thread Is it OK to turn down work?.

    Yep, turning down work that is going to be a PITA or not profitable is perfectly fine and SMART. I find myself turning down more and...

    Apr 17, 2019
  15. Outlaw Graphics 92J rated OhioSigns's post Like in the thread Looking for reflective purple vinyl.

    It looks like Grimco has 3M 5100R series in Royal Purple.

    Apr 3, 2019
  16. trebor8820 rated OhioSigns's post Like in the thread Question Flexi - Measurement Tool - Fractions?.

    I've never seen a way to automatically make it a fraction but if you click on the dimension and go into design central there is a "lock"...

    Jan 11, 2019
  17. K2 rated OhioSigns's post Like in the thread Suggestions What vinyl to use for printed door graphics.

    I've got a construction company that I do a bunch of 13" door decals for. They generally buy 1 to 2 new trucks every month as they only...

    Jan 11, 2019
  18. 3Dsigns rated OhioSigns's post Like in the thread How to apply prints?.

    You can use a normal roll to roll laminator to mount prints or you can get a flatbed laminator such as a RollsRoller, CWT, etc.

    Dec 10, 2018
  19. Pitstop Motorsports rated OhioSigns's post Like in the thread Swatch Table in Flexi 12.

    Right click on the one that you have open. Click on Open Table. Should be the file called Default. In the file bar it should be...

    Sep 30, 2018
  20. jimdtg rated OhioSigns's post Like in the thread Swatch Table in Flexi 12.

    Right click on the one that you have open. Click on Open Table. Should be the file called Default. In the file bar it should be...

    Sep 30, 2018

 


Loading...