Recent content by PixelImola

ColorCrest, Thank you for the follow-up. In reference to cyan and your comment on RGB, the lack of a mention to RGB was my fault, I must apologize to our technician, in the haste to post I inadvertently failed to add after the RYB, RGB to CMYK ie: (whereas RGB, CMYK offers a different view...

Hello Colorcrest, I do regret and apologise for the delay in corresponding but, after visiting the studio (Tuesday) and passing some time with the responsible in charge of the plotters, I had to investigate a question pertaining to a related theme and then I was also distracted by other work...

Hello ColorCrest, Than you for returning and offering a comment. I tried to PM you the files you suggested (Input Output Files) but unfortunately I encountered two errors. 1. with a small zip fil 9 MB an upload file size error and 2. an error, something about unable to send. Please let me know...

To unclebun: Thank you very much for this detailed and impartial report. To quote a few points- I had noticed this, in fact on the Mimaki site there are profiles which are classified as Fully Tested and Profiled, Not Tested yet, Certified; however from what little I have seen it was not...

I beg your pardon perhaps I did not explain clearly. If you can master it quickly good for you, I was merely referring to a problem that can often occur in businesses where in spite of ones desire to make progress, one cannot proceed as desired, ie work steadily, constantly with a given study...

To iPrintStuff, Solventinkjet, Unclebun, ColorCrest, balstestrat et.al. Thank you for your participation and interesting comments, I am sorry for the delay but I was distracted yesterday with other studies. iPrintStuff & Solventinkjet Thank you for the elucidation, I was aware of Onyx, I had in...

To iPrintStuff, Solventinkjet, Unclebun, ColorCrest, balstestrat Read with interest. Thank you very much these comments and suggestions, they are greatly appreciated I will follow this up later today.

Thank you iPrintStuff for this interesting information. We had in fact considered Onyx, together with Caldera, but we have not yet made a choice. May I inquire what persuaded you, convinced you to move to Onyx rather than to another renowned RIP, some mentioned in this Forum. Have you found that...

Hello, Thank you for your input. We are considering another RIP since, from its installation on, our staff have not been enthusiastic with Rasterlink; perhaps it grows on one after use. Considering the setup of our studio, the options available and lacking other advice we had considered Caldera...

Hello, I am posting after some days because I felt obliged to investigate this problem further, obtain some confirmation of the exchanges between our firm and Mimaki representatives and also check the quality of the recent prints in order to see what discrepancies there may still be in the...

I regret the delay in this follow-up and apologise for the consequent lack in rapid response to the recent posts, in particular to some of the interesting points and questions. In the last two days some tests have been run, the results of which have led us to ponder on the methods used for the...

To the members who offered their opinions in the this thread please accept my apologies for this belated correspondence following our recent exchanges. I will try and respond to the comments in this single post, hoping that this will avoid cluttering up the thread and will not contravene any...

Hello, Thank you for your observations and comments. In fact it would appear that you are absolutely right, one of our staff examined the colour curves of the profile at the lowest resolution and there was a notable difference (around -40% M) in the proportion compared to those of the higher...

Thank you for your prompt comment. If we may be so bold as to reply, it is our opinion that any professional plotter, even supermarket inkjet printers, should be able to print red as red. (on standard papers with default inks) We believe that red should be red, at least reddish, not orange...

Hello, We are having problems with the plotter : Mimaki UCJV300-160. It is practically new and still covered by warranty. The dealer is, as yet, unable to help. A brief summary of our main problem is as follows: The plotter will not print red correctly, the hues are faded or worse, are altered...