• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Recent content by shacho

  1. Need Help versaworks 6 perf cut

    Actually, what I am trying to do is cut two circles. The outer circle will be a full contour cut and the inner circle will be perf cut with tabs but with the same force as the contour cut, not to cut through the liner. The intension is when the whole sticker is pulled off the liner it will grab...
  2. EG reflective icc profile for oralite 5600

    I am looking for an icc profile for Oralite 5600 Engineer grade vinyl. i have and Roland XR640 and i alway print 1440 x 720. i dont undetstand why anyone would print at any less resolution. Can anyone point me in the right direction to find this icc profile. or any icc profile for my printer...
  3. Discussion Perf Cut

    I have a Roland XR-640 pro 4 and I am struggling with this as well. In Versaworks 6 you are only allowed a maximum half cut force of 80. I am using Oracal 3164 high tack with an overlam which requires much more force than that. I know if Versaworks 5 you could set the half cut for up to 300gf. I...
  4. Versaworks 6 print / cut crop marks

    I'm having the exact same issue, however, I have the latest firmware and upgrades for Versaworks. Did you ever find a solution for this?
  5. Need Help versaworks 6 perf cut

    not in versaworks6
  6. Need Help versaworks 6 perf cut

    What about the perf cut. What versa works it does is it goes from 250gf when perf cutting to 80gf when half cutting. Are you suggesting if I change the half force to 110 on my machine it will use that as the force for the half cut and ignore versa works but it would use versa works settings for...
  7. Need Help versaworks 6 perf cut

    I am using versaworks 6 with and XR-640 pro 4 and I am attempting to do perf cutting for the first time on laminated vinyl. My problem is the half force only goes up to 80. I typically use about 110 to go through the vinyl and laminate nevermind the backing paper. Can anyone help with this...
  8. window perf 2019 GMC Acadia

    i use optically clear edge tape around the perimeter and still not luck. i have tried using the 94 primer before and i found you can see it on the inside of the window. I think i may have figured this out. i beleive there is a coating on the window... maybe something like RainX that is...
  9. window perf 2019 GMC Acadia

    Hello all, I have put some widow perf on the rear window of a 2019 GMC Acadia and it has come off twice in the last year. I make sure the window is very clean using a general cleaner then finishing up with isopropyl. I even thought it was the vinyl itself so i bought some new Orajet 3675...
  10. publish to pdf with signlab 10

    the png is just a screen shot from signlab. Do you how do i make the PDF look the same as my signlab screen? thanx
  11. publish to pdf with signlab 10

    I have signlab 10 and i like to send out proofs by publishing to PDF so the customer can zoom in and see detail. my problem is when i am publishing to PDF it is the wrong color. i will attach a screen shot of what it is supposed to look like (named before) and a PDF after publishing (named...
  12. Need Help same RGB different color

    does anyone know in versaworks where i check "ignore icc profile"?
  13. Need Help same RGB different color

    A customer sent me 2 files the other day and they both had colors with the same RGB values yet they printed different. The color was close to black. One printed nice and one printed super thick.
  14. signlab profiles for xr640

    I recently bought a new printer and it has been so long I can remember how to had profiles to Signlab VPM. Can someone help me out. thx
  15. Question too much black ink

    I don't know how to do that. I googled it a nothing come up. do you know of a site that can guide me through this process. I forgot to mention that I am using Versaworks Dual could this be a problem? thx
Top