Welcome To Signs101.com: Largest Forum for Signmaking Professionals

Signs101.com: Largest Forum for Signmaking Professionals is the LARGEST online community & discussion forum for professional sign-makers and graphic designers.

 


  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ratings unclebun has received

  1. JR's rated unclebun's post Like in the thread Suggestions Frame for Dibond Sign.

    There are aluminum extrusion frame systems available that your sign would fit into, but the frame will end up costing as much as or more...

    May 27, 2020 at 8:55 AM
  2. mfatty500 rated unclebun's post Like in the thread Boat Registration Numbers Complaint...for real???.

    Gino is correct. The height of letters is defined by the flat letters (like I, T, W, V--unless the W and V have points on the bottom)....

    May 22, 2020 at 1:58 PM
  3. bannertime rated unclebun's post Pure Genius! in the thread Aluminum Trucks... Again!.

    [IMG]

    May 21, 2020
  4. Michael-Nola rated unclebun's post Like in the thread Streaking / Banding?.

    surface contamination on the substrate

    May 20, 2020
  5. Pixels Are Bad Mmmkay? rated unclebun's post Like in the thread How do I remove CLEAR COAT.??.

    So, to fix the problem it has to go to a body shop where they will sand and refinish the whole vehicle. Probably cost $10,000?

    May 20, 2020
  6. decalman rated unclebun's post Disagree in the thread Anyone seeing loads of material shortages yet?.

    Just ran into my first issues with delivery of things. Feather flags (which I suspect are really made in China) suddenly started taking...

    May 20, 2020
  7. decalman rated unclebun's post Disagree in the thread How do I remove CLEAR COAT.??.

    Perhaps you spend too much time on internet forums. The person you were arguing with offered an example similar to the one you...

    May 20, 2020
  8. Pixels Are Bad Mmmkay? rated unclebun's post Agree in the thread How do I remove CLEAR COAT.??.

    Perhaps you spend too much time on internet forums. The person you were arguing with offered an example similar to the one you...

    May 19, 2020
  9. Jed_Dess rated unclebun's post Like in the thread How do I remove CLEAR COAT.??.

    Perhaps you spend too much time on internet forums. The person you were arguing with offered an example similar to the one you...

    May 19, 2020
  10. Texas_Signmaker rated unclebun's post Like in the thread How do I remove CLEAR COAT.??.

    Perhaps you spend too much time on internet forums. The person you were arguing with offered an example similar to the one you...

    May 19, 2020
  11. ColoPrinthead rated unclebun's post Agree in the thread Hello guys i really need your help!.

    I think the problem is that laser toner melts at 110 degrees C.

    May 19, 2020
  12. Lindsey rated unclebun's post Agree in the thread Need Help Sticker print and cut.

    White borders do solve the solvent problem. Letting the ink thoroughly dry is necessary. That takes anywhere from a few hours to...

    May 19, 2020
  13. Andy D rated unclebun's post Agree in the thread Hello guys i really need your help!.

    I think the problem is that laser toner melts at 110 degrees C.

    May 18, 2020
  14. Jim Hancock rated unclebun's post Like in the thread Need Help Sticker print and cut.

    White borders do solve the solvent problem. Letting the ink thoroughly dry is necessary. That takes anywhere from a few hours to...

    May 16, 2020
  15. Joseph44708 rated unclebun's post Like in the thread FC8600 Graphtec Cutting settings for CB09UB and CB15UA-K30.

    The manual actually tells you how to set it all up. There are settings in the machine for each type of blade and the necessary offset,...

    May 16, 2020
  16. signage rated unclebun's post Agree in the thread Unpaid Land Taxes?.

    It's just proof that you don't really own the land.

    May 15, 2020
  17. Andy D rated unclebun's post Agree in the thread Unpaid Land Taxes?.

    It's just proof that you don't really own the land.

    May 14, 2020
  18. Andy D rated unclebun's post Agree in the thread Polishing Bronze Plaque?.

    If they were from Gemini, and you can prove it, or even if you can send them a picture of it and the date of when it was made, they will...

    May 12, 2020
  19. Joseph44708 rated unclebun's post Like in the thread First Laminator Question GFP.

    Hmmm. Went to GFP's website and found this:...

    May 11, 2020
  20. Joe House rated unclebun's post Agree in the thread Need Help Cannot read OPOS marks on glitter vinyl..

    Put a piece of application tape over the registration marks, then use a fine point Sharpie to redraw the marks on the tape.

    May 11, 2020

 


Loading...