Welcome To Signs101.com: Largest Forum for Signmaking Professionals

Signs101.com: Largest Forum for Signmaking Professionals is the LARGEST online community & discussion forum for professional sign-makers and graphic designers.

 


  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Ratings unclebun has received

  1. JR's rated unclebun's post Like in the thread Suggestions Frame for Dibond Sign.

    There are aluminum extrusion frame systems available that your sign would fit into, but the frame will end up costing as much as or more...

    May 27, 2020 at 8:55 AM
  2. mfatty500 rated unclebun's post Like in the thread Boat Registration Numbers Complaint...for real???.

    Gino is correct. The height of letters is defined by the flat letters (like I, T, W, V--unless the W and V have points on the bottom)....

    May 22, 2020 at 1:58 PM
  3. Michael-Nola rated unclebun's post Like in the thread Streaking / Banding?.

    surface contamination on the substrate

    May 20, 2020
  4. Pixels Are Bad Mmmkay? rated unclebun's post Like in the thread How do I remove CLEAR COAT.??.

    So, to fix the problem it has to go to a body shop where they will sand and refinish the whole vehicle. Probably cost $10,000?

    May 20, 2020
  5. Jed_Dess rated unclebun's post Like in the thread How do I remove CLEAR COAT.??.

    Perhaps you spend too much time on internet forums. The person you were arguing with offered an example similar to the one you...

    May 19, 2020
  6. Texas_Signmaker rated unclebun's post Like in the thread How do I remove CLEAR COAT.??.

    Perhaps you spend too much time on internet forums. The person you were arguing with offered an example similar to the one you...

    May 19, 2020
  7. Jim Hancock rated unclebun's post Like in the thread Need Help Sticker print and cut.

    White borders do solve the solvent problem. Letting the ink thoroughly dry is necessary. That takes anywhere from a few hours to...

    May 16, 2020
  8. Joseph44708 rated unclebun's post Like in the thread FC8600 Graphtec Cutting settings for CB09UB and CB15UA-K30.

    The manual actually tells you how to set it all up. There are settings in the machine for each type of blade and the necessary offset,...

    May 16, 2020
  9. Joseph44708 rated unclebun's post Like in the thread First Laminator Question GFP.

    Hmmm. Went to GFP's website and found this:...

    May 11, 2020
  10. ARGENTO rated unclebun's post Like in the thread Need Help Cheap Software for CUT vinyl.

    Sign Wizard from aries-graphics.com starts at $495. If you already have Corel Draw, CoCut from cocut.com starts at $99.

    May 8, 2020
  11. WYLDGFI rated unclebun's post Like in the thread Need Help Cheap Software for CUT vinyl.

    Sign Wizard from aries-graphics.com starts at $495. If you already have Corel Draw, CoCut from cocut.com starts at $99.

    May 8, 2020
  12. Goatshaver rated unclebun's post Like in the thread Need Help Cannot read OPOS marks on glitter vinyl..

    Put a piece of application tape over the registration marks, then use a fine point Sharpie to redraw the marks on the tape.

    May 4, 2020
  13. Lindsey rated unclebun's post Like in the thread Discussion Your Cut Vinyl Work ?.

    Like these? I got tons more.

    Apr 27, 2020
  14. Goatshaver rated unclebun's post Like in the thread Need Help Media Profiles, ICCs and print quality.

    There are very few profiles available to download for that printer. What's available is available through Onyx's download utility....

    Apr 25, 2020
  15. Jackpine rated unclebun's post Like in the thread Not a new font.

    Berlin Sans FB Demi Bold

    Apr 25, 2020
  16. tbullo rated unclebun's post Like in the thread Discussion Your Cut Vinyl Work ?.

    Like these? I got tons more.

    Apr 24, 2020
  17. Notarealsignguy rated unclebun's post Like in the thread Discussion Your Cut Vinyl Work ?.

    Like these? I got tons more.

    Apr 24, 2020
  18. bannertime rated unclebun's post Like in the thread Discussion Your Cut Vinyl Work ?.

    Like these? I got tons more.

    Apr 24, 2020
  19. ColoPrinthead rated unclebun's post Like in the thread Discussion Your Cut Vinyl Work ?.

    Like these? I got tons more.

    Apr 24, 2020
  20. studio 440 rated unclebun's post Like in the thread Discussion Your Cut Vinyl Work ?.

    Like these? I got tons more.

    Apr 24, 2020

 


Loading...