• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Bad Cyan & Magenta output

    It may happens because resonance things. It starts from carriage rail wear, not so good quality or carriage bearings. Small vibrations has a resonance on steel bear, and we cal look it as vertical banding. It may happens because printhead not aligned Also it possible because media overheating...
  2. This printer or software just #*&#*^# hates me!! Whats this???

    Try to print Setup variables from printer’s menu. For see will print transparent black if you will not use RIP.
  3. Question Mutoh 1324 Misfiring Head

    Check the tube to waste bottle. Do you see ink flow while cleaning is in progress?
  4. Does anyone know if there is a way for the printer to bypass reading/detecting ink cartridges?

    What printer model would you like to unlock?
  5. Need Help NEED HELP MY MUTOH VJ1204 NOT PRINTING GOOD

    Try to reduce ink level in cartridges. For this printer level should be 1/4-1/3. 1/2 is maximum. The printhead in your printer is choked by ink.
  6. Need Help NEED HELP MY MUTOH VJ1204 NOT PRINTING GOOD

    What you mean - "refilable ink"? Do you have a picture? VJ1204 does not contained subtatks. So, it very sensetive to ink level in the system. If you use open cartridges you have to think about ink level in cartridges or bottles.
  7. Need Help NEED HELP MY MUTOH VJ1204 NOT PRINTING GOOD

    What ink cartridges are you use? Refillable? It looks like ink level too high and inks dripping from nozzle plate. Or dampers not goog quality.
  8. MUTOH Firmware, 1000ml ink & the truth :)

    If you upgraded just main firmware without heater board firmware - you lost connection metween main and heater board. This case unlock will not help you. You have to upgrade heater board firmware to version what corresponds to main board firmware. Downgrade of firmwares on Mutoh Valuejet is...
  9. Need Help End Of Roll Error Message on Mutoh 1204

    The problem is dirty media sensor. Just open rear media guide and clean the sensor. It installed in "air tube" and may covered ink dust while printing. So, sensor hole taping will not fix it.
  10. Need Help MUTOH ULTIMA 1400D STUCK!!!

    Hold on.... File *.bin for update with PC and file for update with flachcard are different. For flashcard you have to use *.pcc file. Another option - update with COM port cable by attached manual for critical situation.
  11. Need Help MUTOH ULTIMA 1400D STUCK!!!

    I think you can try to update with PCMCIA flash card. It is hardware option with direct access to plotter's memory.
  12. Question Wiper error

    Check the wire from sensor. It may be you fix it while replacing the maintenance station.
  13. How do you unlock the mutoh valuejet 1304 so it can work without chips

    It should be FOC for existing customer.
  14. How do you unlock the mutoh valuejet 1304 so it can work without chips

    The printer worked without smartcards. So, card serial serial number did not read by printer. Firmware update is not erase smart cards disable code from the printer.
  15. How do you unlock the mutoh valuejet 1304 so it can work without chips

    Maybe your printer was reset to default parameters. Sometime it happens. If smartcards on your printer was disabled by service code, try to upload same code again.
  16. VJ1204 Cannot Open Port

    What is IP setting for WiFi on your notebook? If DHCP then please check your IP for WiFi is not in same range as LAN port for direct connection to the printer.
  17. Question white dots on the print

    It is maybe too high static on media. And air humidity is too low.
  18. Please help. Installed new print head

    It is not Mutoh format of head rank. Heads from Mutoh has 24 symbols on the rank,
  19. Please help. Installed new print head

    It is not 100% necessary, but extremaly recommended. Prithead will work with wrong head rank but in wrong mode.
  20. Need Help xerox 8265 to mutoh spitfire 65

    Try to remove all cartridges a little and switch ON the printer. If same E9 error will display - you will need install and activate new SIM-card. Sometimes it may happen if you downgrade or change manufacture code of the printer.
Top