Search results

Hi all, not a good day today with my falcon printer. First started out with a blocked pump, 20 minutes later and all cleaned out and back to printing a nice print. Then after a foot of printing, it decides to stop. Now, I've had this before and its usually the ip address. So I changed the ip...

The heater on my falcon wasn't as hot near the right hand side as the centre and left side so I took the casing off and tried to get 2 wires to unclip. I could see the problem straight away. The heating strip had come away from the platen. But I lost my grip and dropped the platen ending in...

I bought a rockhopper 2 in need of repair. Was told that it didn't work at all. No power to the unit what so ever. So I bought it as it was really cheap to see if I could do anything with it and if not strip it for spares. Anyway, I got it back to my unit and tried switching it on. And the guy...

Is it possible to get hold of a mutoh falcon cpu chip rather than buying a whole new motherboard? If so, where can I get one? Cheers Mark

Its got to the point where I'm lost in what I'm doing at work. I've got job sheets and post its all over the place. Do any of you have a job production board at your place of work. I'm looking at putting one together but can't figure out the best layout. I need it to have things on like, to...

I bought a used rockhopper 2 in need of repair and I'm almost there with it. The only thing is the heads had been taken out and cleaned but not put back in. I've now put the heads in but the cables don't seem to be in any order or are marked for which cable goes to which head. Can anybody help...

Hi all, Don't know if this should be on the Roland section or the flesign forum, but here goes. I need to add an abrassion guard to prints on the pc-60. I have an abrassion guard refill as I couldn't find an original cassette. Due to this there is no proper barcode sticker for it. I called the...

Does anybody know what barcode to use for the abrasion guard cassette? And how to actually use it in flexisign? Cheers Mark

Been running flexisign 7.5 now on my pc for around 3 years and never had a problem. Today, all of a sudden its started to play up. When I click to open flexisign it starts to load up and then it opens and 2 seconds later it dissapears. I thought it may be hidden somewhere, but I opened task...

Does anybody happen to have a copy or could email me a link to a maintenance manual please? I have the user manual but need the service manual. Cheers Mark

Anybody have or know where to get hold of either a user manual or a service repair manual please? JUst obtained a pc60 and haven't got a clue how it works. It prints and cuts but prints badly, doesn't pick up the right colours and I've changed the cartridges with new barcodes and when it does...

Hi all, I downloaded the free estimate trial and have had a good look around it. I'm thinking its definately something we need in the shop as were hopefully expanding soon and need to have a better production run instead of just jotting on note pads. I have a few questions regarding this...

I hope someone can help, and I know banding is something that theres loads of possibilities it can be, but I've tried everything. I have 2 mutoh rockhoppers and one of them has started banding black lines across the media. At first I thought that it was a bit of fluff that had dragged across...

This has been happening for a while. Probably all the time I've used the machine. What ever I print it doesn't come out the exact size. I'm using flexisign rip and lets say if I print a 6x2ft banner it will come out about an inch shorter on the length and a fraction of an inch shorter on the...

I think thats what its called. Its the end caps you insert into the roll of banner or vinyl and then slides on to the roll hoder. Its not the black end stops where one is fitted to the holder with a circlip. Any ideas where I can get some, prefer somewhere in the UK. Cheers Mark

I'm running an agfajet sherpa 43i from flexisign with a network card. Been running it for 18 months and today it stopped working. I've checked the connections and the network name and address and all fine. It starts to print but then halfway through just stops and says on the control panel...

Looking for a bit of help regarding converting my mutoh to solvent. I already have one thats converted to run eco solvent inks and I've just bought another one to convert in the same way. The first one I bought is actually an AGFA jet sherpa 43i and the second is a MUTOH falcon, both 6 colour...

Hi All, I'm new to large format printers and am a bit unsure of icc profiles. I'm running flexi 7.5 and I have a agfajet sherpa 43i (mutoh rj6000 /rj6100) and has been converted to eco solvent inks. I'm in need of icc profiles for this 6 colour printer. Now because its not originally an eco...

Hi all, I've aquired an old rj6100 and its in need of a service. I've got a service manual, 2 new heads, dampers, capping station and pump. I've put the pump in, capping station, dampers and heads. I've set the head rank accordingly. But now what do I do. Do I need to run a system clean...

Hi everyone, my names Mark and I'm from the north of England. I run a sign shop in a small village and produce cut vinyl in house but still source out digital print and banners. I've been running the shop for a little over 2 years now and really enjoy what I do. I stumbled across this site...