• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Mimaki JFX 2513 EX - Rasterlink

    Hello everyone, Want to know what resolution acrylics are printed on. We use 600x900 12-pass but sometimes get banding, Especially in the blues. I do have about 5 missing cyan nozzles that I replaced with the Nozzle Replacement feature. Should I be using 24 pass?
  2. Epson S60600L

    It says not enough ink to perform a cleaning. Before even if I pressed NO to clean and continue printing it would not. Yes to cleaning was my only option. I did notice today when I pressed NO to cleaning it did continue printing. Maybe my firmware upgrade did fix this.
  3. Epson S60600L

    Hello My Epson S60600L runs on a bulk in system. Most of the time it makes me change the ink bag there is still ink inside. There must be a good 200ml + left in them. Called Epson they upgraded my firmware but it did not help. Anyone having similar issues with this type of printer?
  4. JFX200-2513 EX Showing Ink Empty

    Hello all, My flatbed says my primer is empty. The bottle is half full. The bottle expired yesterday 6/2/21. My supplier has no ink until next week and Mimaki has no explanation. Got a new, but expired bottle (2019) but does not work either. Says expired. I know a while back I was shown...
  5. JFX200-2513 EX White Ink Banding

    Thanks All. NEw print head was installed last week. Seams that was the problem.
  6. Wall Material Recommendations???

    If money is no issue 3M Envision 480 works very well. 3M 8624 is good too but takes much longer to install.
  7. JFX200-2513 EX White Ink Banding

    No nozzles missing. Its perfect.
  8. JFX200-2513 EX White Ink Banding

    Not Much. Printer is 1 1/2 years old. This is the 2nd white/white/clear/primer print head. It was installed last summer. 80 of our prints use no white. We print white maybe once or twice a week.
  9. JFX200-2513 EX White Ink Banding

    We print acrylics using a 600x900 Rasterlink acrylic profile. At the default value of 12 passes the colors print great. When we add a white background I have to change to 24 pass or my white has thin banding. Which is very noticeable especially when printing light colors such as a sky. Now...
  10. Suggestions 2 inch acrylic print

    Thank for the suggestions. I decided no to risk it especially for 1 small acrylic.
  11. Suggestions 2 inch acrylic print

    Hello everyone. Trying to print a 2 inch thick acrylic on our Mimaki JFX200 2513. We lowered the head gap to 1.5 but printer still wont accept it. pressing enter after it reads the media height wont work. Im afraid to go any lower and risk a head crash.
  12. Question Help! Cold Laminator keeps wrinkling prints!

    We had the same issue with a laminator and the problem was the top roller was warped. The pressure on the center was much more than the sides. If possible have a tech check the pressure across the rollers. If it was used primarily for mounting that could have been the cause of the warping...
  13. Graphtec FC9000 Print and Cut Issue

    All within the pinch rollers. Even did a test just using the middle 24 inches of a 54 inch roll and same problem. I do notice the the crop/ margin marks always print about 4 inches inside the graphic. On my previous Graphtec 8600 they would print on each corner.
  14. Graphtec FC9000 Print and Cut Issue

    Using a Graphtec FC9000 with Onyx Thrive. We print a bunch of print and cut decals. When it comes to placing on the graphtec to cut, it cuts all the decals fine except for the last row on the side of the media. It only cuts half the image. We have tested with smaller jobs to make sure we...
  15. Epson Surecolor s60600L error

    Our Epson S60600" suddenly turned off. When we tried to turn it back on got an error: Call for Service Note the following and call for service Code 3000[HC030K6] After a couple of times it looked like it was turning on correctly but when the PrintHead carriage was going to park it self it...
  16. Wall Graphic Print Quote

    Welcome to Florida! They give everything way down here.
  17. Sheet Cut

    Hello, I am having the same issue. Did you resolve it?
  18. Mimaki JFX200-2513 EX Clear printing

    Trying to print clear on a metal and foam but the clear seams to be banding. Nozzle check is fine. I tried multiple ways of printing clear but I can't get a smooth clear finish. I would appreciate any suggestions. Thanks in advance!
  19. Pinch Roller Marks (?) On HP Latex 260 (L26500)

    Could be the vinyl. I have had similar issues with cheap banner material. Have you used this vinyl before? Try with another vinyl and see if the same happens.
  20. Tabletop banner stand

    Orbus.com
Top