I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
Not sure what to do at this point? We have never had luck laminating anything that is over 36" wide and tend to shy away from jobs that require long vinyl laminates. We have a 62 Seal Pro S which is probably a great laminator, however, we simply cannot seam to figure out how to laminate with...
I have a job to print "in restaurant" menus. These will need to be somewhat rigid and will better survive with a PVC type substrate. I will be laminating them after printing.
My question is, does anyone reading this know of any media I can use for it? I have found plenty of media but only...
I am debating whether to sell my graphtec FC7000MK2-160 plotter. I purchased it 6 months ago from a local wrap company that went out of business. I hooked it up and ran a few test with it and never have turned it on again. We just don't run cut graphics that often and think it will be...
I purchased a Seal Pro S laminator (used) back in August and have yet to get it to laminate over 8 feet long without getting bubbles in the prints. I realize there have been posts like this one in the past but I have several questions that are not answered in any one forum. Here are my...
I am in the middle of wrapping an IS300 (my own car) and this is the 2nd time I have wrapped it. The first time I wrapped the car with Avery Supercast Vinyl which was a breeze when it came to the bumper, however, I am now wrapping the car with Oracal 970RA Matte Black and no matter what...
I have a customer who would like bubble gum pink racing stripes installed on her truck. If I install 3m IJ35 calendared vinyl with cast lam will it perform ok? Does anyone have suggestions for alternative material? Thanks.
I am wrapping an IS300 and need some advice on how to remove the door handles and side molding. Does anyone have any experience with this car and know how to remove some of the hardware?
I may just leave it on if it is too difficult but I would think the door handles should be fairly easy to...
Does someone know what this font is? I want to use it for a haunted house banner. I thought it was unlovable but it is quite different. Thanks for any help.
I am interested in purchasing the Epson GS6000. Can someone tell me who carries this printer and will make a good deal on one. Also can someone tell me from experience how this printer compares to others. I know the gamut range is incredible but are there other benefits to it.
Thanks...
Can anyone educate me as to my limitations with wrapping a car in Matte Black and overlaying a Green Foil Vinyl to market my business. For one where can I buy foil wrap vinyl? Will the Foil Vinyl stick to the Matte Black vinyl. Can you see foil vinyl at night or would I have to buy reflective...
Can anyone shed some light on what cast matte black vinyl/laminate is good to use on vehicles? Also if anyone can tell me where is a good place to purchase it from. My supplier (Denco) does not carry this and they have to special order it.
Thanks for any help.
Chad
I was hired to design a logo for a company that formulates health care supplements. I have 4 different versions for all to critique. Please help me see which ones have potential (if any) and what I can do to improve them. I submitted the first one to the company to use in the interim but have...
First off I hope everyone had a Merry Xmas (if you celebrate it). First day back for me I have a client who needs magnets for his car but would like to have them made with rounded corners. I have never rounded corners on material like this and do no know how this could be done. Would anyone...
I am wrapping a 12 foot trailer with rivests and would like to here your experiences on wrapping over the top of them or pulling them out and replacing over the wrap? I am wrapping with Oracal calendared wrap vinyl and their cast laminate.
Also it is a bit weird, the rivets are an 8 star...
I ripped a 300mb file in versaworks today and it took 30 minutes. Is this a relatively normal amount of time to rip a file that size?
I am running a computer (2 months old) with a AMD Athlon II dual core processor and 4GB of ram. Is this sufficient for ripping mainly vehicle wraps and store...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.