• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Help with a Font ID

    thank you
  2. Help with a Font ID

    Can anyone help to ID this "AMBULANCE" font? Unfortunately I didn't have any success with find my font on this one.
  3. Pressure knob adjustment question on enduralam

    Is this supposed to bottom out here? (see picture) 13 year old laminator that I have successfully been using without much needed adjustment. However lately one side of the laminator began to give me issues running cast lamination (fingering would start towards one side after about 3-4' of run...
  4. Font ID needed

    Thank you!
  5. Font ID needed

    Could someone help me out with this one? I can't get FMF to recognize because of the arc.
  6. Cross contamination in magenta lines - frequently

    Seems like when my machine sits over the weekend it always experiences cross contamination in the Magenta lines. Any idea where to start with diagnosing this issue? 14 year old VJ 1204 - currently on 3rd maintenance station and 2nd print head
  7. Font ID needed

    Could anyone help me with this one? Unfortunately I didn't get any dings from FindMyFont.
  8. Cross contamination wont go away

    Thank you.
  9. Cross contamination wont go away

    My printer ran out of blue ink over the weekend and all my line got cross contaminated on my VJ-1204. All lines went to black. I ran solid C,M&Y through the line to get the cross contamination out. The C and M cleared fine. The yellow hasn't. I have run about 30% of a Y cartridge / a...
  10. cross contamination of M lines

    Thank you so much for your input!. I'll start with some fresh dampers and see if it will eliminate the issue.
  11. cross contamination of M lines

    My Mutoh 1204 sometime experiences cross contamination of my M ink? When the machine sits a couple days without printing or over the weekend sometime when I come in the magenta lines are cross contaminated black. I have to run the M ink solid for awhile to get the M back to printing the...
  12. Bad Cyan & Magenta output

    After running some vinyl with the covers off, playing with the tensions, I noticed the PF motor wasn't turning. I gave the belt some subtle manual persuasion and it got the wheels turning and they have been still spinning with a few print restarts. Now with the PF motor spinning it seems my...
  13. Bad Cyan & Magenta output

    I looked back and I do have the tensioner set to the same location it was set before I changed out the carriage. However there is alot of slop in the tensioner, to the point where it wobbles. I'm experimenting now with adding some tension slowly to see if anything levels out
  14. Bad Cyan & Magenta output

    I have a image attached of where the belt is riding on the cr motor. The belt is butted against (rest on) the lip that is on the bottom of the drive gear of the CR motor. Should there be more tension? will this belt ride higher on the cr gear if there is more tension? I also highlighted in...
  15. Bad Cyan & Magenta output

    Thank you so much for all your knowledgeable input. The bearings from the previous carriage were all spinning freely, non were seized. I inspected the race way, there visually isn't any wear at the points of contact of all the bearings. I did mess with the belt tension at the time I did all...
  16. Bad Cyan & Magenta output

    Thank you guys for all your input. I'm processing it all, thinking back this issue probably did start when I changed out the carriage assembly. I swapped out the assembly with an entirely brand new one. You asked about the "bearing raceways": Are the bearing raceways the 2 bearing that are...
  17. Bad Cyan & Magenta output

    If there was an issue with print head alignment wouldn't it effect all colors? Only the C and the M are doing this. I find it tough to believe a carriage bearing is at fault because I replaced the entire carriage assembly within the last 3 months. I didn't quite follow about the media...
  18. Bad Cyan & Magenta output

    No the carriage is pretty quiet. I replace the CR motor within the past 2 months. Also the carriage assembly was replaced as well.
  19. Bad Cyan & Magenta output

    Any idea why I might be getting this type output from C & M? the Y and B that print are super solid. I'm printing on a VJ 1204. The nozzle check I ran was flawless. I'm thinking possibly a heater or damper issue? Just looking for some additional input. I'll probably start by changing the...
  20. Alignment on media issue

    That was it. Thank so much for the reply. You got me fixed up.
Top