• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. R

    How much for (5) 27" tall printed on reflective?

    How much for (5) 27" tall printed on reflective?
  2. FC7000 Contour Cutting Problem ARMS

    Thats funny. I just did that. Thanks alot for response.
  3. Falcon Junior No Color Print

    Installed NEW capping station and now works fine. You need a good seal to draw ink thru.
  4. Falcon Junior Capping Station Color Seal Problem

    Replaced capping station with NEW one and fixed problem.
  5. FC7000 Contour Cutting Problem ARMS

    Using Signlab. Cutter sees all 4 Reg. Marks and goes back to start and travels to second one and keeps going after I send cut command. Cant figure this one out.
  6. National Park Service Reflective Logo

    I need (5) 27" tall reflective prints of their shield logo. PM me. Thanks
  7. Falcon Junior Capping Station Color Seal Problem

    Thats what I have to do to get Black to work. Color still has hissing sound when pulling. Squeezed hose at capping station and it stops air release...therefore I don't think the head is sealing with capping station well.
  8. Falcon Junior Capping Station Color Seal Problem

    The Black ink can be drawn thru waste line but color seems to be sucking air. Just changed heads and capping station. Do I need to prime or is their an adjustment to make it sit tight against seal? Have ink to heads but can't pull thru. Thanks
  9. Falcon Junior No Color Print

    Just changed heads and capping station. Can't get ink to capping station. Black ink pulls thru OK and prints perfect in test. Is their a way to prime it to start flow. Have ink to dampers. No blocks to waste tank air pushes back thru.
  10. GULF type replacement face.

    They were not squared off faces. Had a little arch to them. Custom form is too expensive. I thought I saw someone down South that made them.
  11. GULF type replacement face.

    I remember somebody making replacement faces for these "Junk" signs. Does anybody know of anybody who makes them. Thanks
  12. Does Not Print!

    Did a wash with Black Ink. Still no printing. Motherboard has D7 and D15 RED LED's flashing. D12 is always ON. Any help is appreciated. Head fuses OK.
  13. Does Not Print!

    Yes. I bought it and it included supplies worth the cost of sale. So Im not into it very much. Thanks for your help.
  14. Does Not Print!

    Finally got Black to pull thru. Color must have leak. Will replace "O" rings next week. Still doesn't print black in nozzle check. I think I checked right fuses. All OK.
  15. Does Not Print!

    Wants to do a print test...But nothing comes out. Getting "O" rings next week. Entered NEW Head Rank Numbers. Still nothing. Getting the two beeps when it starts to print. Can't pull any ink out of heads when in capping station thru waste tubes. Thanks for looking.
  16. Does Not Print!

    I dont have it hooked up to computer yet. Just doing test prints. I did pull ink from bottom of dampers but I did not get anything out of waste lines with syringe. May be the fuse. Where is it located on board. Thanks alot.
  17. Does Not Print!

    Just replaced print heads and dampers. Pulled ink thru dampers and still no ink comes out on test print. Mutoh Falcon Junior 38. Please advise. Thanks in advance.
  18. Mutoh Falcon Outdoor Junior SDMP 38 Waste Bottle

    Thanks for the help.
  19. Mutoh Falcon Outdoor Junior SDMP 38 Waste Bottle

    I Just pick up a used unit and there was no waste bottle with it. How do I replace it? Thanks.
  20. Graphtec FC 7000 Cutting Problem

    Settings Tool: CB09ux Offset: +1 Speed: 15 Force: 18 Quality: 2 How do you reset the plotter? Will I lose settings? Camera is acting up. Will post pics later. Thanks for your help.
Top