• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Die cutting on FC9000

    Do you have a step by step guide to do this?

  3. Boat club flags and burgees, supplier recommendations

    I'm in need of a supplier that can produce flags and burgees. TIA

  4. Edge printing white on clear static cling

    Clean everything twice before you send it! Stupid dust bunnies!

  5. WTB Gerber Edge Setup and/or foils

    I have some unopened foils that we will not be using. They are for the older style of edge. I'd have to make a list of what we have.
  6. DaveD

    Thankyou for the tips.

    Thankyou for the tips.
    • DaveD
    • Profile post comment
  7. DaveD

    Hi troy, The flatbed is being used about every other day. We are still running the three roll...

    Hi troy, The flatbed is being used about every other day. We are still running the three roll to roll printers non stop. We haven't made a large enough shift or addition to the direct print industry to justify the new flatbed. I need to tap into some leads that will boost that section of our...
    • DaveD
    • Profile post comment

  8. Will an Epson S80600 fit through a standard interior door width?

    I had to take off the take-up real and a couple brackets on the heater unit on ours to fit.

  9. Opinion Need A New Heat Gun

    We buy these 6 at a time and always try to keep two on the shelf in the box. We get about 6 months of hard use out of them.

  10. 8' Table Throw today

    Can anyone produce and ship an 8' table throw today or tomorrow? I'll need it in hand in Washington State by Thursday.

  11. Advice with stocking router bits

    What do you have for a V groove bit?

  12. Any Freelance designers out there?

    We are having a hard time keeping up with our design workload and are in need of some help. If you're a freelance designer looking for some work please message me. Thank you!

  13. Advice with stocking router bits

    We just had our Summa F1612 standard router attachment installed. It came with one multipurpose bit (500-9852). I'm looking at Summa's "router bits overview" and I don't get a a lot of detail and guidance as to what bits I should have in stock. I'm not opposed to using other brands but as a...
  14.

    3m TSA-4 or YelloTool Wall Roller

    I like the look of that tool. The heat gun becomes the second hand hold.
  15.

    3m TSA-4 or YelloTool Wall Roller

    I think you're right and I'm sure I'll end up getting one or the other.
  16.

    3m TSA-4 or YelloTool Wall Roller

    Does anyone out there have a 3m TSA-4 or Yellotool Wallroller that they are willing to part with? Any recommendations on a tool that's not $400 plus?

  17. Help me Decide an Upgrade: Roland VF2-640 or Epson 80600 Printer only?

    So we just got our new S60600L installed yesterday and the first run (for money) is a large vehicle wrap with all grey tones. Mind you I had to adjust the curves and set up a custom profile, but the quality and speed is amazing. You walk away for 5 minutes and the first panel is already done...

  18. Epson S60600 maintenance

    They had a $5K rebate that ended on the 31st. Now they have a $3K rebate. I test drove the S40 the morning of the 31st. (That’s the only model in the showroom) and was lucky enough to place the order that day for the S60600L. Spent the day today making room for it and the Summa F1612 I picked up...

  19. Epson S60600 maintenance

    I was sold a $20K knife and the printer came with it.

  20. Epson S60600 maintenance

    Thanks for asking the question. I had questions about this also. I just bought the S60600L on Monday and we should see it next week. Hybrid design are you using the Onyx RIP? We use Caldera and I’ll look into the media advance settings. FYI this community of shop owners had great info that I...

  21. Who is using the Epson R-Series for vehicle wraps?

    I'm ready to bring on a new printer and I've been looking at the Epson R-Series. We have three HP Latex printers now and will replace the oldest. We do both signage and wraps and like the latex for the "no wait" lamination. The issue I have is color consistency and I'm going to go with the...
Top