Search results

It is direct

It is a direct connect

After sending a print job to my SP300v, it starts to print then stops and says "now processing". It did it last time i printed but i was able to get it to start over and thought it was just a goofy glitch. Now tonight i can't get it to continue to finish my print job. Anyone else had this...

I installed a new motherboard and am having problems initializing it to push the peck.exe. I backed up the peck from my old board and am going to try again tonight.

I know this is an old post, but i am having the same problem. As soon as i plug my machine in I get the "sum error" and can't shut the sub power switch off. What did you do go get it in the mode to push the firmware?

I'm looking for help on this. Installed new motherboard, as soon as i plug in my SP-300v it displays the sum error. I can't power it down to run peck.exe. When i connect the usb cable, it doesn't appear to be connecting to the computer. I reinstalled my old board, upgraded my firmware and backed...

Did you ever figure out your problem. I'm having problems. I tested the F2 & F3 fuses and think they are ok but now I'm questioning myself. I'm thinking about changing them just to rule that out. Thoughts?

I'm thinking about ordering the F2 fuses and replacing both to try and eliminate those. Thoughts? Otherwise I'm leaning towards carriage board.

What did you find your problem to be? I'm having problems with mine; changed the heads and cups. Still no ink. Getting an error message when i boot up in service >Cartridge > IC Check. I checked the little fuses and they appear to be good. I wondering if the Cartridge board could be bad. Any...

I did that. I'm getting some ink, not a lot because i have the new heads and caps but can't get ink to them. I can't get ink in either head. I checked fusses on my motherboard and cables, all seem good. When start up in Service mode and run >Cartridge >IC Check I get an error right away on Slot...

I removed the heads, reinstalled and verified my head numbers. I checked the lines for leaks clear back to the cartridges. What i did discover when checking my ink levels is it is only recognizing black. There is a black X through the other cartridges. It beeps if i remove them so the chip is...

I did not try drawing ink through the caps. Do i draw with the print heads seated? I sounds like it is purging, but still not pulling ink. I will tear into it again tonight.

I was having problems with my printer loosing cyan and black. I soaked the print heads in solvent twice 24 hours the first time, 48 hours the second time. Still wouldn't work. I ordered new caps and print heads. I have installed them, ran ink fill, head clean and ink fill again. I'm still not...

I believe that is what I installed but I will try it again. After doing it I get the error message. "The program can't start because AdobeXMP.dll is mssing from your computer. Try reinstalling etc."

I am installing Versaworks on Windows 7 64 bit. The disk I have is Version 2 and I need to get it updated. I have went to Roland's website and downloaded the updates. The directions are not very good. Can someone give me the directions to get the updates done and get my print up and running...

After much investigation I have a hole in the tube in the pump assembly. I have placed several calls and find this has been a problem and Roland resigned the pump because of it. I ordered the new pump along with the maintenance kit as long as my machine is tore apart. But I am very discussed...

First I thought my print head was plugged but after following your directions to clean the print head found 1 drain tube plugged. I clean it out as far up as the purge motor but don't know how much farther it is plugged. From the looks of the red ink inside it has been for more then 1 day. Do...

Drain tubes plugged First I thought my print head was plugged but after following your directions to clean the print head found 1 drain tube plugged. I clean it out as far up as the purge motor but don't know how much farther it is plugged. From the looks of the red ink inside it has been for...

Clogged heads I hope these directions help my problem. Is the procedure posted done on a Roland? If not does someone have directions for a Roland? I have a Roland SP300 and believe I have a clogged head.:thankyou: