• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Question Vinyl material buckling

    When cutting as the material comes out of the front it starts to buckel when it goes into the cloth basket....get creases in it...have to babysit the entire run as it cuts and goes back and forth. It seems to be tracking fairly straight when we put it it....does it on sheet runs and roll runs...
  2. Arlon High Tach Mutoh 1324

    Whats a good heat setting for using Arlon High Tach ?
  3. Arlon material with Mutoh

    Anyone using Arlon High Tach material on a Mutoh 54" ...if so what is a good heat setting ?
  4. Mutoh Cartridge Issue...can't pull out 1324

    Has anyone experienced not being to pull a cartridge out for replacement ??? What do we need to do ?
  5. Gold Reflective Color Match

    Does anyone have a good PMS, CMYK or RGB code for a gold reflective ?
  6. Question Remove 3M 8150

    Can anyone share a good method of removing 3M 8150 clear from windows that the product has only been up for two weeks ? It was used for a short promotional deal on five windows. Any feedback is appreciated.
  7. Wrap premasked install ?

    Any one out there ever install a premasked, no lamination horizontal 3M ControlTac no lamination ? Got graphics from another shop out of state to install on van ....
  8. Roland SP300 / Laminator

    For Sale...Roland SP 300 with Wasatch SoftRIP.....cloth media baskets front & rear, complete set of new ink cartridges and new black head replaced in January2015. Price includes 30" Daige cold laminator. Upgraded to larger printer and laminator. Located in South St.Paul, MN ...buyer responsible...
  9. USB Cable Hookup

    Does anyone know the maximum length of a USB cable you can use from the computer to SP 300 or any large format printer without issues ?
  10. Print & Cut issues on SP 300 after upgrading to Flexi 11

    We have major issues with the SP 300 on the cutline being off by up to a half of inch ....any suggestions ? The printer is 13 years old....we are using Flexi rip.....
  11. Looking at a 1324 54"....feedback ?

    Currently have a Roland 30"...looking at upgrading.... looking at a Mutoh 1324 54" printer...any feedback on the unit positive or negative..any help would be appreciated.
  12. Slack in the upper carriage cable guide ??

    Is there suppose to be this much slack in the upper clear guide of the carriage cable after I replaced it ??
  13. Roland SP 300

    Is there anyone out there that has a Roland SP 300 that could take a close up picture of the carriage cable and plastic guides. I replaced mine with a new cable and guides and I want to make sure mine are installed right before I test the machine. Usually I take a picture before I start a repair...
  14. Clear Vinyl - Fire Engine Gold

    What clear product is recommended for a protection overlay for Fire Engine lettering using 3M comply black with FDC Engine Turned as the second layer ? I've seen it on the trucks but don't know if it is just a clear laminate used for digital prints.
  15. Flexi 8.6 won't save design file

    Anyone experience Flexi 8.6 not saving larger files ? It starts to save and about 35% of the files goes good then error message that it won't save.....?????
  16. Fire Engine Lettering

    I have a question on the process used for lettering....I've seen the gold leaf vinyl, not SignGold place over black 3M comply with a laminate over it with about a 1/8" outline for protection. Can anyone share the process for this and what is needed ? Thanks.....
  17. Installing Lintec Material

    Has anyone installed Lintec Window Digital Print material ? What is the going rate for installing this material ?
  18. Roland Service Mode

    Does anyone know how to get the service mode unprotected on a SP300 ? I want to print out my history report of the machine. Thnaks....
Top