I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
I have a 2022 Mercedes AMG GLE 53 Coupe that I want to put the PPF on , I've done the ceramic coating to it but I want a little more protection .
Does anyone know what brand to go with and where to buy it ?
Thanks
I figure I'd poke around to see where I could get the best deal on ink , the US distributers have went up a lot due to inflation and shipping cost are very high .
I went to AliExpress and found Jetbest for $18.00 and $12.00 shipping . Yes it takes longer as the International shipping but I...
I looked all over the place , ordered some on eBay weeks ago but finally gave up and checked Amazon . I got it and its perfect . Everything fits nice and snug and you get 10 feet. $6.99 and 1 day shipping.
For the underside of captop and pumps...
As you can see about my captop I have a puddle of ink , I just cleaned the whole captop assembly yesturday . You can see by the motor there is a big puddle of ink . Eventually it will leak down by the drain bottle and end up on my floor .
I did install a new captop , no idea .
No idea why but with lamination my D75 will not find the first mark with lamination . If I cut lamination off from the area it will read fine . It will also read all other 8 or 10 marks WITH lamination on it .
So why does it read all OPOS marks with lamination but the first one ?
I've done a few tests with this and it seems to work pretty good but the ink squality isnt good , even printing in high quality mode. I'm using the curing powder and still the ecosol ink ..... again just testing .
Can you tell me what profile I should use to print on the matte finish ?
also...
I have a VS 300i and I tore if down thinking the pulley bearing were bad that connects to the scan motor... Turns out the scan motor itself is whats making the noise .
Is there a way to tear is down and replace bearings ? or ......
Do I run it till it can run anymore ? or fork out the 500...
As I was told by a few different people / places . On the Summa D75R 30 inch cutter , a 3rd pinch roller can NOT be added . If you want a 3rd roller you need to purchase a different model and that is $5000.00.
After looking at my machine over and over and over again I said ... there HAS to be...
I'm curious if maybe they make oversized wheels for the VSi300 ? Ever since I got this machine I could never do contour cuts over 30 inch long sheets , I normally cut 25 inches wide by 30 long .. MAX . Anything over 30 inches = forget it .
I was thinking MAYBE if I added bigger wheels it would...
So I finally found a way to add a 3rd pinch roller to my Summa D75 . Issue is it will detect the first available roller that it can see. Is there a way or is there something I can remove on the pinch roller assembly of the one I want to add ?
No idea who long these things are supposed to last but I have a lot of leakage now . I bought them 7 months ago. Can anyone tell me the best place to get them from ?
I've been at this for about a week , I've printed 2 color charts and can't seem to get the color I want .
I am attaching a picture hoping someone has a value I can use that is close to it ?
Thanks
I've posted this question before but never really got an answer dialed in .
#1 I do contour cuts perfect fine on my Roland up to about 30 inches in length (13 mil material )
The sheets I need to print and cut ( 13 mil material ) is around 50 . If I dare to do that it goes in the trash.
So...
I just got this brand new today and I've noticed my contour cuts are off . I did the calibration but it didn't help anything . I'm scared to send my big 50 inch printed sheets to this cutter ..
Any tricks ? With testing such a small job I'd think it would be dead on . ?
Test material in a...
As the title says , I'm just trying to find out what size the Summa cut marks should be ? Somewhere I thought I saw 3mm , but I also saw 10mm as well ?
Also , will a ROLAND blade fit in the normal Summa drag knife setup ?
Thanks
I'm planning to buy this on Monday as I hear the tracking is GREAT with this machine . I have a Roland VSi 300 and if I try to do contour cuts over 45 inches i'm doomed , been like this since day one.
Question is , Will summa see the Roland crop marks ? or what do I need to do to be able to...
I've been dealing with this for a long time and I still haven't figured this out.
I'm starting to do big print job for a company out of Canada , I'm printing big UTV Graphics and nested the sheets at 50 inches long , just because some of the panels are huge. I did a big bleed on them and still...
I have a Roland printer and since 2013 I've always exported as EPS , finally I've hit my max disk space and with 2tb full of files I figured I'd try to print PDF ..and it doesn't seem to have any quality differences so I may continue like this .
What format do most of you all print in ?
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.