• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Need Help HELP!!! Onyx 11

    You, Sir(or Madam), are a life saver. The 10.2 driver worked! Slowly coming back to life again, Thank you!
  2. Need Help HELP!!! Onyx 11

    Still looking but nothing so far.
  3. Need Help HELP!!! Onyx 11

    Thanks, I'll give this a try.
  4. Need Help HELP!!! Onyx 11

    Hi Guys, Just has a catastrophic HD failure and had to rebuild. I had Onyx 11 and was able to install from a downloaded install file, but the printer installer files are gone. Anyone have the hard copies (dvd, cd) I need a prninst file for a mimaki JV33-160. Onyx only has the files for 12...
  5. New JV33 Firmware with MAPS

    I saw this post on Signs101 from a while back. Wondering if you ever located the 5.7 prm with MAPS. Apparently Mimaki decided to stuff it away in order to sell newer printers.
  6. Need Help JV33 misfire black channel

    Ok I feel like an idiot. I cleaned and cleaned but couldnt get it right, until I found the smallest fragment of material stuck to the end of the platen. I guess better to be stupid than buying a new head huh
  7. Need Help JV33 misfire black channel

    Hi It looks like that, but under the loop you can see that it is actually a black head firing onto the magenta bar. It comes in waves in that it seems to get heavy, then after a few passes begins to reduce, then it comes back. I really think its an overheating of something, but not sure what.
  8. Need Help JV33 misfire black channel

    I dont know what happened. I uploaded them again. They show up now.
  9. Need Help JV33 misfire black channel

    Im getting a misfire on one of the black channels. When I print an image, it looks as if Im getting a color bleed, like when a damper gets a few drops of different ink in it. Upon further inspection of the color bar that is printed along the margin, I noticed a set of black dots printed directly...
  10. Ultimate JV3 Diagnostic Challenge, open to any tech or other superpower

    Im pretty sure these are factory, Ive been bitten by china pumps before. As noted previously, I can print high speed, not slow.
  11. Ultimate JV3 Diagnostic Challenge, open to any tech or other superpower

    The pumps are relatively new (3-4 months old) Dampers are new too. It only does this when I run slow speed. I can go into #test menu and print full test patterns on each head and it puts the ink down fine. I think if I were truly having a starvation issue, it would not be able to print at...
  12. Ultimate JV3 Diagnostic Challenge, open to any tech or other superpower

    First off, yes, I do still run a couple JV3s.... My oldest machine is a 160s running 6 color config. I began having what appeared to be starvation issues. I noticed while printing 720x720 slow speed. I would begin to lose approximately 5 - 10 nozzles per pass, until pretty much, no print at...
  13. JV3 Parameters needed BAD!

    I found a factory manual and got em....thanks anyway. I will be back with something more daunting
  14. JV3 Parameters needed BAD!

    Hello all, I came in this morning only to find my JV3 160SP on and stuck with Error 04 Flash Rom. Looked up the code to find it being the main board. Not to worry right? I have a 250SP that has no heads in it right now and thought Id rob the board from it. All went perfect until I tried to...
  15. Mimaki JV33 Parameters

    Does anyone out there have a list of the JV33 parameter meanings. Some are obvious and others make no sense at all, and since there are a bazillion different settings, it would be nice to know what they represent in English terms. I ask because I have a JV33-130 machine that has a used...
  16. JV33 Used Main Board replacement

    changed parameter I changed the parameter to 3 for model, but it still boots as 160 machine. Also, now it only shows 4 cartridges on the led instead of 8
  17. JV33 Used Main Board replacement

    Hi Guys, I have a real head scratcher. I purchased a used Mimaki JV33-130 that needed a main board. It was a good enough price for something to tinker with. Anyway, I found a great price on a used mainboard and bought it too. I put the board in, booted up (without errors) and noticed it...
  18. Firewire / IF20 issues with a JV3

    We had a similar issue. Sometimes things went well and sometimes not. Its the cable length. I dont know why it works sometimes, but it does. It would be better to use a 10' cable and 15' cable with a repeater in the middle. We ended up going with a Fire-Nex cat5 extender. It took care of...
  19. Profiles for Onyx - Mimaki JV3 ultra

    Im looking for any profiles that someone may have made for the Mimaki JV3 printers using the Ultra driver from Onyx. I cant find anything for 3M products using the 6 color configuration with SS2 inks. Any help would be appreciated.
  20. Cool Mod to my JV3 250

    I know someone has probably already done this, but here goes anyway. We bought a JV3 250SP a while back and it prints great, problem is that it is not really practical for the smaller stuff that we print on the JV3 160. So we decided to hack up an older 160 machine we have in the shop and...
Top