Search results

I always get a message when my ink runs low from all of my colors before a job is started, except for the Cyan color. Anyone know why this may be happening? Not a huge deal, but if it runs out during a print job, have a light streak in my print. Using VersaWorks and again only happens with the...

I know this thread is super old, but I've just heard about Kapco vinyl. How does it ( 3mil air egress ) compare to Oracal3165GRA or the 3M calendared air egress vinyl?

I have a roll of the 3268, but have not tried running it yet. I might be asking you for any tips on that.

I've done a couple of things that's helped eliminate 99% of my problem.... I reduced the heat some....... if the rolls sits on the machine, the material tends to wrinkle over time if the pinch rollers are left down, so make sure you release the rollers and allow the material to lay flat, then...

Okay, I'm going to reduce mine jsut a tab and see if I get better results. I mainly use Oracal 3651 and 3165.

I'm using the default settings and the print Heat is at 45C and the dryer is at 50C..... is that about right?

ok, I'll try that. Thanks

The 300 doesn't allow you to adjust the head height ( that I know of ) and it only has 2 rollers..... 1 for each end..... Printer in house in controlled environment too. Thanks for the response.

Thanks for the pic.... I've been using R-tape Conform and really like that stuff, but I may have to try something different.

I have a Roland SP300v..... My prints have been getting messed up from the head hitting the material. It doesn't jam or anyhting, so I usually don't see it until the job is completely finished. I can understand the edges curling up sometimes causing this problem, but how is it hitting the center...

Please do show pics if you can.... I really need to figure out something different. For some reason, I just can't get the tape started without wrinkles.... After wasting a foot or 2, then it straightens out and I can place my vinyl in front of the roll and apply with no problems..... It has to...

It releases fine from the vinyl, but the problem is that it's so tough to apply, that it's stretching. After I apply the tape to my work, it starts to draw up and wrinkle / tunnel, before I can get a hard squeegee on it. To me, paper tape is usually hard to unroll when you get close to the end...

Could you explain a little more about method / conditions? If I might be doing something wrong, I would love to figure it out. I have other rolls of the same type and they release 100 times easier than this roll. Thanks

I just got in a new roll of RTape Conform Series. It's a 24" roll. It's all I can do to pull some tape from the roll to create a tag end to stick to the table. Then I use my BS to apply..... having to use great force to push the roll. When I'm done, my workdraws up I guess from the tape being...

Took 10 of them into my local Staples this past week and they took them. That's great news for me!!!

I work off a table top for my surface..... I don't usually rub my tag end that sticks to the table with a hard squeegee. I'll try that and see if it helps. Thanks

I'm not sure what has changed, but latedly, everything I apply application tape to that is 24" up to 30" wide, I get wrinkles in my application tape right at the start. I use a 32" BS to apply my tape and I use R Tape Conform. How I apply...... I lay my graphic on my flat work surface...... I...

Bobby, are you still providing this service? I know this thread is old, but was searching to see if there was any changes in what people do with their ink cartridges? I have the Roland 220 cartridges.

Yea, that's what I was thinking. I clicked on the un-nested files and they were still positioned like I had it before, but when I went to nest them back together, it automatically rearranged them and I lost the original position I had. If I would had cut 1 of the files and then reset and cut the...

I did a job in Versaworks and had 2 files nested together. Crazy me accidently un-grouped them after they were printed. Is there a way to set it back up to cut, or am I screwed and have to reprint everything?