• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Mimaki jv33 banding like someone is taking a miniature rake through it

    Figured out mine as well. On the 3rd new roll of vinyl, the banding stopped. Frustrating!! Thank you to everyone for all their help.
  2. JF - 706 Error help?

    Okay, so i replaced the lamps (like i always do). Everything went fine. When i hit remote to turn the lamps on, i got a error msg. 706 Error UV1 Interlock I've unpluged and plugged back in the power cables that run the lamps. I've taken out and put back in the lamps. I really don't know...
  3. Mimaki jv33 banding like someone is taking a miniature rake through it

    Still getting the banding. The banding is only on reds (moreso dark reds/garnet) and purples. Test draw is still perfect. Just confused on what to do and adjust? I've changed my media comps from -20 to +20 and everywhere inbetween those.
  4. Mimaki jv33 banding like someone is taking a miniature rake through it

    Attached are pics of my test draw and media comps. You can see in the media comp, that the two bars aren't touching, but in each bar, there are some dotted lines that do overlap. Thoughts?
  5. Mimaki jv33 banding like someone is taking a miniature rake through it

    I'm a novice when it comes to the printers. How would i go about adjusting this? I'm going to take a photo of my media comp run.
  6. Mimaki jv33 banding like someone is taking a miniature rake through it

    I'm having similar issues. My test draw is perfect. No missing or deflecting nozzles. I've run the media comp(s) and were the top bar and bottom bar meet, it's seemless (no gaps or overlaps). However, there are 2 streaks in the middle of each bar??? I've also run the drop position and...
  7. Help Needed for JV33 issue

    Thanks SL. I used some alcohol to clean the sensor. It fixed the issue. I didn't see and debris on the sensor, but it worked. Again....thanks for the response! The picture helped out nicely as well.
  8. Help Needed for JV33 issue

    Hopefully someone can help me out. I had a pretty bad head jam/strike yesterday. The vinyl we were using half way through the material they had taped 2 sheets of vinyal together. When the 33 got to that area, I assume (since i stepped out of the printer room) that the heat lifted up the vinyl...
  9. Cyan head not filling w/ink JF1631

    Well, after realigning it 100 times...the damper finally filled up. Strange.
  10. Cyan head not filling w/ink JF1631

    I need some suggestions here. I changed the Cyan head on our JF 1631. Everything went well (putting in the head). I went to run a hard clean to fill up the head and i noticed that the damper didn't compress. I checked the alignment. Clean again....same issue. I then replaced the...
  11. JV3 not pulling ink

    I've done "Nozzle Washes" and have run an "Ink Fill Up". I have not done a "Head Wash"...I don't know how to do one. I didn't try to pull ink through the damper. I totally forgot about that. I'll give that a try ASAP. Thank you.
  12. JV3 not pulling ink

    Long story short, our JV3 wasn't used for over a month (operator was fired). Everything worked perfectly fine before. We just had a minor issue with one of the Yellows not reading that a ink cartridge was in. Anyways, Last week when i ran a test draw, only half of the Cyan printed. Nothing...
  13. JF-1631 strange error

    Still have the issue. Someone mentioned that it could be the Station PCB board. Said it's underneath where the inks are. I opened it up and there is a board that says Station E400579. I can't find that online anywhere?!!?
  14. JF-1631 strange error

    I need to edit the last two error messages. SYSTEM HALT (1) 133: PCB STATION That's followed by 133: PCB STATION PIO SLIDER OK Thoughts anyone??
  15. JF-1631 strange error

    Where to start..... I changed out a head and when i powered everything back up, i burnt one of the ribbon cables (from the mengta head i replaced). I replaced that and got the error message; System Halt (1) 11d: PCB SLRLY_F1 Figured out it was one of the fuses on the PCB Station. We...
  16. JF 1631 Head Cable

    Thank you Robert. We found someone and had them shipped next day. I appreciate your response though.
  17. JF 1631 Head Cable

    Does anyone know where to order one of these? It's the cable the goes from the head (where the grounding wire screws into) to the board? One of my cables shorted out.
  18. JF 1631 dampers, purchase

    Here's a link to the damper i was talking about. http://www.digiprint-supplies.com/mimaki-jf-1631-damper.html
  19. JF 1631 dampers, purchase

    Anyone know where the cheapest ones to get? I saw on digiprint supplies they were pretty expensive. Wondering if that's the standard. We've purchased them before, but they didn't seem that expensive.
  20. JF Cyan issues

    So, it's still not working, but i was able to use a syringe and pull ink through the damper....but still not able to get it to suck into the head....
Top