• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. S/c read err

    Yes, I sent.
  2. Mutoh vj 1204

    Both ways are accessible. But most cases I does it remotely via TeamViewer sesion. Only need connection to printer and Internet. Because end-user is scarry to use new software. Price is same like your.
  3. Mutoh vj 1204

    I can do it. I am opened many printers from all VJ generations included 1624, 1638 this way.
  4. Mutoh vj 1204

    Yes, sure. Not so hardly. But why to do it if possible to do it by software in few minutes without screwdriver and mainboard send.
  5. Mutoh VJ1604 with DX5 head

    Sorry guys. Of coarse, the best way is use Original printhead from Mutoh. No any problem and all work perfectly. But you asked about possibility of use DX5 from Epson on Mutoh printher. I am explained, yes, it possible. And price for Epson printhead two times cheaper. On picture you can see...
  6. Mutoh VJ1604 with DX5 head

    Head Rank containd some information for perfect working each printhead (voltages, mode for piezo, etc...) and use for fine tuning printing mode. This info collected while printhead produced and unique for each. These parameters can be coded by various format. So, Epson DX5 and Mutoh OEM rank...
  7. Mutoh VJ1604 with DX5 head

    Actually, DX5 printhead has a few modifications. We don't look to original in this moment. Most of all types of Epson DX5 are coded. And impossible to print more than approx 90 cm width. You have to install addition chineese decoder for use this printhead. But some printhead can be used without...
  8. S/c read err

    I have solution. Sent PM.
  9. Mutoh 1204AS CR Encoder Error

    Did you check Encoder values in diagnostic mode? If OK, you have to replace motor driver on mainboard.
  10. mutoh 1624 longstore

    I think your problem is ink filled switch inside cartridge holder like on picture. First of all you have to check and clean switches. Procedure can be aborted in diagnostic mode.
  11. Reset ink on vj1204

    Printer read ink volume automatically from smartcard on cartridge. No need to do anything if all OK with sensors in printer. Just put new cartridge and continue printing. But it possible to switch printer in special mode for working without smartcard. This case any cartrige (even empty) will be...
  12. Reset ink on vj1204

    What you mean "Ink counter"? What is messge on display?
  13. Vj 1204

    We can see yellow lines through all printout. Maybe flatcables bad connection on printhead, carriage board or mainboard. Or flatcable pins jammed. Or printhead fault. Please disconnect and check again flatcable pins. If all OK, you have to replace printhead.
  14. mutoh 1324 e068 error

    I am asked because some wires in head cables used for Encoder circuit. So, all looks good. It can be coincidence, and some parts burned. This case only one way to find the problematic part - replace one by one. In my opinion I would start from disconnect and connect CR cables on mainboard and CR...
  15. mutoh 1324 e068 error

    What is antistatic wrap? Self-adghesive or not? Can you move carriage to the middle while printer OFF and press Porek key? What will happen this case? Same move and error?
  16. Life Times CR Motor

    Actually, you have to check CR motor. No need to replace if working fine. Just go to Maintenance mode and reset counter.
  17. mutoh 1324 e068 error

    Did you unplug power cable while replace dampers? Did you press power key for remove rest of electricity on capacitors? In 1324 model not so easy to replace dampers. And possible you moved head cable a little and short cirquit happened.
  18. Vj 1204

    Dishhobby Can you please show nozzle check?
  19. Mutoh vj 1204

    I am opened my Mutoh ValueJet printer without disassembling. It possible to do it remotely.
  20. Vj 1204

    Source of this CR problem can be: - scratch or grease or dust on T-Fence strip; - dust or parts of hair on CR-Encoder; - wrong tension of CR Belt; - bad connection of J207 CR Board connector; - broken CR Motor (electric collector inside); - pulley on the motor not fixed and can be move on...
Top