• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Please help me...scan motor errors!!!

    In service manual check chapter carriage wire tension adjustment . If your scan motor was in your store for years in bad condition mybe it's damaged, although the old motor look so bad but you have no scan motor error with it try back it and see if pass error .last if you sure of all your...
  2. Please help me...scan motor errors!!!

    First that video is for old motor? What the scan motor error code number have no one ? -Make sure that the ENCODER SCALE doesn't make contact with the ENCODER MODULE and also ENCODER SCALE is between the slit of the ENCODER MODULE. -In service menu do linear encoder calibration...
  3. Versacamm keeps saying CARTRIDGES DISCONNECTED

    Have this error when starting printer or after press button to make carriage move or after sending job from pc and what model printer you have . Have you check the trailling cable which connect main board to head carriage are connected well ,remove the top cover check if there any wrinkles on...
  4. Head alignment

    I have this service manual just pm your email .
  5. Verscvamm vp 300 Feeding Vinyl crooked

    -Check the fan that's work or not from service menu (check fan ) it's work as vacuum holding material and work with the wheel to good feeding. -clean the fan blowing the dust maybe there is paper make it jam. -from versawork (Job Settings>Printer Controls> Other Controls> Vacuum Power) set...
  6. Service Mode for Roland XC-540...

    This is the passward read attachment next.
  7. sc-500 Vacuum?

    I mean that fan speed change according to roll length not roll width, according to the heavy of roll 5 meter more heavy than 2 meter more resistance to pull need more speed fan to feed it. When sheet setup choosing piece mode that mean you set piece not length more than 1.6 meter so fan will be...
  8. sc-500 Vacuum?

    ""I am assuming the platten is the actual silver strip with the holes in it that "suck" the media down."" -No it's not never take it off your printer will be parts on the ground ,it's the front cover with one hole for paper sensor easy to remove just lose the screw you can see it. - For...
  9. Versacamm SP-300 Yellow bleed on prints

    Mybe it's too far but check the fan work or not, from versawork (Job Settings>Printer Controls> Other Controls> Vacuum Power off/normal/strong) set strong, if material not set well the head will touch it and print lines, do that after cleaning cap / wipper every part in parking head area . If...
  10. Roland Sp-300v Printing with a Red Hue

    Check the yellow ( damper ,tube ,cartridge ) mybe magenta ink back to yellow line because clogging in the cap and the cap tube clean it or replaced.
  11. vp-540 Cyan going nuts

    It's look from photo a certain nozzle mybe (20 nozzles) that not work good delay firing ink do next: - check that there is no lose in the head screw tied good and the head setting okay. - move carriage to maintenance area check any thing stuk on the head clean it, note if there any physical...
  12. Grainy bitmap printing Roland SC-500 & Flexi10

    Sorry I'm thinking that flexi have some profile go checked and it have none, hope somebody here sharing some profile or back to roland colorchoice (RCC) .
  13. Grainy bitmap printing Roland SC-500 & Flexi10

    from output setting choose use color correction( color setting tab will be on ) open it go rendering intent >bitmap under others choose absolute colorimetric then print see what result you get ,test the rest setting list from others. Read the help you will know every setting for what.
  14. What is causing this?

    All your problem look around the encoder strip last thing can do after cleaning tied the screw which catch the encoder strip from left hand side be careful too much tied will cut the encoder strip from other side if not work replace the encoder strip get new one.
  15. Stumped... Roland SP-540v with a weird print pattern... ideas?

    Try clean the wiper and cap then by syringe pull some ink from cap tube or drain tube then do test print if having same test print i think the pump no problem you can open cover press on the cover sensor while it cleaning and see it work or not , pump sound it usual or not . There's no one...
  16. What is causing this?

    Do another test change the BASE PIONT see if the problem appear in anywhere on wide printer or always on same point. If always in the same point make straight line by eye or something material to encoder strip note any scratch on it ,the black line must bee same color if any wrong liquid touch...
  17. What is causing this?

    Do another test change the BASE PIONT see if the problem appear in anywhere on wide printer or always on same point.
  18. 5.1.1 up date no server

    I don't if that help this file below have some troublshooting read problem 16. If you have no problem on network try reinsall versawork, when do updating disconnect the antivirus and never do anything while that on versawork open file or riping or anything.
  19. IP address for soljet 540

    Open color rip Print>Setup>TCP/IP list insert same IP adress that printer have except last number 192.168.100.(this number).
  20. sc500 No Magenta on test print.

    Another thing check the wiper must be clean it's have 2 side smooth and harsh I'm not sure think the harsh must be out smooth in when wrong set sometimes make test print look bad because it's not cleaning the head face good and make a drop dot on the material when printing .
Top