• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Need Help Part Found On Vj-1304w And Rj-900x

    Does anyone know what this part is called? They've started wearing out and falling off and I don't want the ink tubes rubbing against the inside of the machine. Also, does anyone know of a quick fix for this? I used tape for some of them, but it's been leaving behind sticky tape residue on...
  2. Need Help Ink Drop Out

    dampers
  3. Nozzle On Vj1204

    Can I delete an old post? I'm worried other people might be searching for a solution for the same problem and try what I said up there before finishing the thread. I don't know why I assumed everyone uses water-based ink just cause I do. :P
  4. Nozzle On Vj1204

    So what would happen if you poured distilled water into the waste tank?
  5. Nozzle On Vj1204

    ohhhhhhh my bad, cleaning fluid then.
  6. Nozzle On Vj1204

    Try filling the cap top with distilled water, then run a clean cycle right away before it drains. Then try another nozzle check to see if it improved.
  7. new mutoh 1624x banding

    I do mine at 250mm instead of 500mm. Is there any benefit to performing the adjustment at 500mm?
  8. RJ900 Sublimation Printer Clogged

    You can use a solution of 1 part windex, 10 parts distilled water and fill an altoids can (or similar shallow container) and set the head in there for about an hour. Worked for me more than once.
  9. Question: Does anyone leave their mutoh printer on standby over long peroids of time?

    Depends on your climate. If the humidity isn't right it could clog before 3 days, I'd wager.
  10. VJ 1604 clogged nozzles

    Did you try soaking the head in cleaning solution?
  11. 1304 ink problem

    It affected both yellow channels.
  12. 1304 ink problem

    One of my 1304s had this problem with yellow. The ink line that runs along the long ribbon cables was rubbing against the inside of the printer until it wore a hole through and was letting air in. Have you taken the top off and inspected the lines? It can be a very small hole, and you should...
  13. Pressure Roller for Mutoh VJ 1304, 1324, 1604, 1614, 1624

    Is it $13.00 for just one of those? Is it OEM?
  14. mutoh 1324 printing issues

    What about the other colors? Can you post a picture of a nozzle check?
  15. Uneven feeding (picture attached)

    tim99, alot of play in the direction they roll, or side to side? Because they move side to side a little bit. VanderJ, what's the story on shaving down the big ones? Have you seen this in action? $26 per roller is laughably outrageous. I wonder if they even realize how ridiculous that is.
  16. Uneven feeding (picture attached)

    Also, is there a way to know when the pinch rollers are worn? They look the same as the other ones..
  17. Uneven feeding (picture attached)

    The gritted roller is pretty smooth, unlike our other printers that feel like sandpaper. Also I'm pretty sure the pinch rollers have never been replaced. Has anyone here ever replaced the roller before? Not really sure what to expect from a part replacement like that. VanderJ, does...
  18. Uneven feeding (picture attached)

    Does anyone have any other ideas? I'm desperate, we can only print certain things on this machine now and it's seriously cutting into potential business. :/
  19. Uneven feeding (picture attached)

    I just fed it about 30-40 feet without taping it to the take-up. It did the same thing, but also slowly moved to the side a few millimeters while I was feeding.
Top