Search results

Hello, the mainboard on my Sp-540v wont power on the printer.. Problem happens after power cut. I've tried another mainboard (from another printer), it starts Yippie.. Can i retrieve the parameters from the dead mainboard? The green led on the mainboard is ON - Green Led on Carriage board...

Hi there, Since last week, I have been facing an issue with UCJV 150-160 where black unwanted lines is been mixing with yellow color. Cap adjustment done - Negative & Positive pressure checked and within range - wiper good - waste pump looks to be working fine - cap absorber new...

Hello guys, Vs-640i 7 colors, is printing gradient - Shadows and some other colors with a magenta tint.. Using Versa 6, tried different profiles same problem. See attach pictures. Flex cables have been cleaned - Dampers and Captop replaced - Head alignment checked and no anomalies found. When...

Hi team, Have anyone encountered similar issue on long run print outs? Above 1mt50 the color changes. we are talking about a Vs-64o 6 colors using Genuine Roland Inks with a 2 months old captop. Any idea?

Hi Team, Hope you are doing fine. Need help, dealing with a Vs-640 6 color eco max ink. The color at the start of print is not the same at the end of the print. The printer uses CMYKLcLm versaworks 5.5.1 version Firmware 5.10 Notice that the Cyan test on the left is not the same as the...

Hi everybody, Has anyone come across " Feed Motor Error 0022" on a VG-640 running on TR2 inks? Strange that a feed motor gone bad.. I'm suspecting the FM3 servo board. Shall access the service mode and seek for a report.. Yours, Alex C

Hello everybody, Having a gx-24 plotter which is not detecting the usb cable.. Is there a way to fix this issue out without replacing the main-board? I've considered to replace the ic driver chip M66291 GP-2, very tricky job tho.. Yours,

Hi there, dealing with this issue for quite a long time now unable to sort it out.. Vs540 4C eco Max inks.. New Captop, dampers replaced, i even swop the magenta ink tubes on top of the dampers the problem remain on same side. Before printing the test print is good. Print launched High...

Hi Team, Trust you are doing fine. Im having an issue with SP-540V... kind of banding The prints mostly on magenta are having llines. The nozzles are firing correctly but still lines are present on Magenta.. Test made with Heater off.. Any advice? yours, Desire C

Hi guys what can you tell me about the RF-640A.. A contact is selling his RF640A, he is using third party RIP software, i wanted to use VersaWorks cause Versa is friendly. The printer wont accept Versa? Any idea why? Yours, Al

Hi there everybody, Hope you are fine.. I've just acquire an LEF-12 Roland UV Printer, its a nice little printer, when printing on glass the ink will not hold, it was said that it can print on most material. Is there a setting to be done? I have read about a...

Hello guys , colors are mixing up from magenta/yellow and Cyan/Black.Using Roland Inks. Im suspecting the pump but just to be sure before going forward. Have you ever encountered and solve this particular problem? Colors are not sharp as before. Thanks . Alex

Hi Guys, im installing a new 3.2mt Chinese Printer UD-3208P 4 colors. Using Maintop as ripping software and using PrintMon USB3.0 as print management software. I've run the alignment and calibration done good, when a print is being launch, the colors are not aligned, as if im printing 3D...

Good Morning to everyone, I've acquired from a friend a large format printer, these chinese printer, namely an Audley S7000-x5. The only problem actually is that it is not printing at all. Cleaning & pumping are working fine but when printing nothing on the media. The printer uses 2 print...

Good Morning to everyone, I've acquired from a friend a large format printer, these chinese printer, namely an Audley S7000-x5. The only problem actually is that it is not printing at all. Cleaning & pumping are working fine but when printing nothing on the media. The printer uses 2 print...

Good Morning team, Having an issue with a VS-640i using WH & MT. Using Max2 inks. The print head and captops were replaced in may 2016. In Oct 2016 the white was firing fine but now feb 2017 not even a drop of white on the media.. Firmware 2.00 on Printer...

Good Morning, Guys im dealing with a problem with a VP-540 color Problem.. The same pdf was printed in October 2016 same media, same profile, same ink (Roland ECO-SOl Max) and now the colors are completely different. Try the same pdf artwork on another VP-540 same ink, same...

Good Morning Ladies & Gentlemen, Im having some kind of problem with a GX-24 the USB is not responding anymore 'not connceted' I've even try via the Serial port also but no good.. Any help how to fix out this issue?? Thank you, Alex

Good Morning, im having a fujiflm dx100 ( Epson d700) printer, the light cyan head shows clogging signs. Is it possible to have a product guide to have the lifetime of the : Print Head. Capping Unit Dampers. Thank you for your help...

Good Morning, Having an issue with an SP-540V, when lauching a print it will Rip then move onto the print bar, stays here for about 30-45 secs then dissappears. The status would change from Printing to Not Conncted. No print at all .. I have deal with this kind of problem...