I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
I have some old equipment I need to get rid of. $800 takes both.
The Mutoh printer is fully operational and has a media take up roll on it but it needs a new print head and lines. I used this printer up until a few months ago but not daily so little by little the head became clogged and it has...
I'm trying to contour cut some decals on FC 7000-130 using CM2. I have both the plotter and the controller set to HPGL. There is plenty of material around the registration marks and all marks are being read fine but then I get a Error 1 Instruction not recognized message and it doesn't cut the...
Does anyone have a 7000 series cutter running with Wasatch and willing to help me check some settings?
I've been posting a couple issues lately but I still need just a little help.
I replaced the Y motor and the plotter will cut fine in GPGL mode using Cutting Master 2 and CorelX6 (vinyl only)...
I thought I had my Y position error fixed, after cleaning rails etc. it worked great for a little over a week but long story short I ended up replacing my Y motor.
The Y position error is gone and the plotter initializes normally, senses the media length and width just fine and will do the cut...
Apologies for the lengthy post but I know there have been a few posts on the Y Position Error on Graphtec plotters from time to time and I wanted to share this hoping it may help some of you that encounter this problem. I feel your frustration! Good news is, your plotter might just be dirty and...
This happens very sporadically and there's not much rhyme or reason to it.
This has happened a handful of times the whole 11 years I've owned this printer and on long prints ...the printer looses connection with the TCP address and stops printing. I get a Winsock 10054 error. Thought maybe it...
I recently bought a Mimaki CG-130 FX plotter from a friend for a good price and figured it would be a good extra plotter. He's switched directions in his business (installations only) and no longer needed the plotter. At the time it was in service his employees were the ones operating the...
I have a Mutoh VJ 1204 running Wasatch RIP version 7. Started getting connection issues this week off and on. It started on Tuesday but I thought it might just be static in the air since it's been cold and dry here.
Tuesday I got a "Can not connect to TCP address Winsock error 10054".
Today I...
I was hoping that someone who has a take up system for a Mutoh 1204 could give me measurement specs using a micrometer so I can make a new part. It is the part that is attached to the media bar and sits down in the rollers on the motor that turns the media bar, pictured below.
I recently bought...
It's probably a setting I can't find somewhere but right click paste won't work, Right click menu seems to load a bit slow as well.
Drag and drop when importing not an option either.
Everything else is working great and fast.
Recently upgraded from X6 to X8.
Any of you Corel Pros have any...
My Mutoh ValueJet 1204 just started a whistling noise.
It's hard to tell if it's coming from the print head or over where the capping station is.
Anyone have ideas?
Thanks
A customer wants me to letter a galvanized culvert. 30" in diameter x 14 feet long.
It's going to be stood upright and a "cap" put on it to look like a grain tower.
It's a new culvert so there's no corrosion on it but I've also read that there's special steps in preparing the surface for paint...
Are any of you familiar with Winsock errors and what to check out when getting them?
Just started getting this message when printing. Winsock Error 10054.
I have a Dell
I am printing with a 1204 Mutoh ValueJet using Wasatch RIP 7.0
Everything has been working fine and thought maybe something...
Suddenly my pinch rollers won't raise.
I raised the lever so I could change some media change and although the lever raises and lowers, the display panel says "lever up", & the media rolls froward and backward, I can't get the rollers that hold the media down to lift so I can thread media...
I'm going to buy a 2'x3' cnc router...either the Shop Sabre or Camaster Stinger 1.
Just having a heck of a time deciding.
Those of you that own one or the other could you let me now what experience you have. What you like /dislike?
The reason I'm not going with a larger machine is that I don't...
American Tempo 2538 Automatic Flatstock Press
Prints flatstock up to 25" x 38".
The machine works great and we have been using it to print coroplast yard signs and political signs.
Nothing wrong with the machine, I would rather have a the room for a CNC router.
I have this listed on Craigslist...
Customer wants HDU with....
.....drumroll please.... Two sandblasted HDU signs with wood grain look, Papyrus as the font 40" x 60" for less than $500.00 total :ROFLMAO:
What a way to end a week... my stomach hurts from laughing!
I'm going home now hope you all have a wonderful weekend
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.