• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Sign bracket for parking signs

    these look legit! thank you!!
  2. Sign bracket for parking signs

    Hello All! I’m having trouble finding this type of bracket so that we can install some parking signs into a concrete base for a shopping center. Anyone know where this type of hardware can be purchased? Any feedback would be greatly appreciated.
  3. VP-540i cleaning cycle during printing

    My machine was having the same issue (VS-540). I updated the firmware and everything appears to be working fine again. Im halfway through a print now and the heads haven't cleaned during. Keeping my fingers crossed. I appreciate the help!
  4. Roland VS540 service manual

    Thank you so much!!
  5. Roland VS540 service manual

    Hello Mr. Bert! Would you still have a copy of the service manual for the VS540. If you can send the link that would be greatly appreciated! Thank you for your help.
  6. What kind of vinyl this could be?

    I agree, if youve worked with 180 and installed with IJ35c you would definitely be able to tell a difference, regardless of installing on a flat or contoured surface.
  7. Need Help Looking for Peck Software to replace mainboard parameters on VP540

    Hello All! My mainboard on my VP540 went out and I am in search of the peck software so I can grab parameters on my existing board and replace. Ive already downloaded the copeck software from the Roland site, but its not letting me grab the parameters. If anyone can point me in the right...
  8. Suggestions for applying vinyl on textured plastic polycarbonate lockers?

    Have a client wanting to apply their company logo on some plastic textured lockers that are outdoors. Has some kind of slick teflon coating on it. I did an adhesion test and applied some oracal 751 with some primer 94 and heat with no luck. Any suggestions?
  9. 10yr Old Wrap Removal Suggestions

    Have you ever done a wrap removal like this? Im just wondering since I have not but here is my math/ logic. 5 Gallon bucket of Rapid Remover - $250 1 week Rental of machine - $600 1 work week (5days) of hired help 3 guys @ $15 per hour/8hour days - $1800 Lunch - $250 Total is $2900 cost...
  10. 10yr Old Wrap Removal Suggestions

    Lol! I just removed a very small section that was already lifting up and it wasnt too difficult to pull off. Thats not to say the whole thing will be like that. I did see that literally every rivet was tented and when I grabbed my plastic scraper and went around it the vinyl was very brittle...
  11. 10yr Old Wrap Removal Suggestions

    Here are some pics of the wrap. It will deff have to come off. Wrapping on top is not going to work. closeups My plan is to rent a high powered gas 3500hp Hot Water pressure washer to do the initial removal and some good old fashioned rapid remover and plastic scrapers for any left over...
  12. 10yr Old Wrap Removal Suggestions

    Not sure what the condition of the current wrap is. Doing a site survey this Tuesday. If its not cracking then I will consider wrapping on top, with the disclaimer that the work will not be warrantied. I came across this method while doing more research. What do you guys think about doing...
  13. 10yr Old Wrap Removal Suggestions

    I dont think what they are using is methylene. They have no face mask on as they are spraying it and they are using their bare hands to pull it off. On the video it says its a mixture of bio-degradable chemicals. Im going to mix rapid remover with something and try to come up with my own...
  14. 10yr Old Wrap Removal Suggestions

    I called and left numerous voice mail messages and no response. I dont think they want to share their "secret recipe". I thought sharing is caring. They would make bank selling that stuff haha.
  15. 10yr Old Wrap Removal Suggestions

    We have a client that is wanting to rewrap their 18 wheeler box truck. We will have to remove the wrap that has been on the trailer for at least 10yrs (woohoo). My normal "go-to" to removal is using a heat gun/torch and rapid remover for any residual adhesive. For larger areas I will use a...
  16. Need Help Vehicle Wraps

    I took the 3M training class for vehicle wraps. Its pretty pricey but worth the cost. Im also based out of Houston. If you need any help with vehicle wrap installs, I would be glad to help you out.
  17. Hello from Texas...yeehaw! (not really but that is the cliche lol)

    Hello all! Newbie member here from Texas. Started my first job in large format digital in 2001 as a graphic designer. Worked there a few years then went to small format offset printing for a while. I started my own company last year and focus on Design, Print, Film and Installations...
  18. Siser color print

    Siser easyweed colorprint is the best material, Ive used so far. Make sure to follow the application instructions. I like the fact that it is thin with a softhand and almost looks like screenprint.
  19. Thick line attributes? Outlines? Strokes?

    What software are you editing the graphics from? This happens to me all the time, depending on the software used (I work in CS6). Easiest solution (in illustrator) to preserve the appearance of the text is to select all, Object path- outline strokes. Select all again - then combine all using...
  20. WorxMedia

    Always learning and willing to share my mistakes so others dont do the same...lol.

    Always learning and willing to share my mistakes so others dont do the same...lol.
Top