Search results

Ok, I've taken pictures of where I am so far. I've had my headboard serviced by a tech and he put in 2 new transistors and 2 new fuses. When I got my headboard back before I installed it back in I noticed some of my ribbon cables were crossed... 2 were in the wrong connector port. So before I...

So I purchased a OHM reader to test the 3 fuses on my headboard and the readings are all different. I recently sent my board out for repair and my tech put in 2 new fuses and left my old one in that was giving good readings. I turned on the machine and did a test print and bank C is not firing...

I am in need to buy the after market 20/20 Color Roland 22 Series Ink - I will be in Orlando on Monday so if you know any in Florda I am willing to drive and pick-up. I can't afford to wait I need it on monday for the light cyan and cyan inks.

do you know if there is anyway to get around having the printer dump my inks? When I turn on the printer it asks me to "set ink type" when I select the option that its a CMYKLCLM inks it then asks me to confirm drain bottle is in place - when I select enter it one by one goes thru each ink color...

I keep getting this alert on the screen that says wrong ink cartridge when I put the new ones in. I am using 20/20 Color Roland 22 Series Ink purchased from grimco.com I have always used this type of ink so I dont know what is causing this. I should also add. Right now the printer is asking us...

Hi When I turn on my roland sol jet XC-540 it is asking me to select the ink type either Esol Max CMYKMC or E-Sol MAX LCLM - When I click esol max CMYK one it says install drain bottle then it says filling ink.... then it says remove Sol CL inks 2,3,8,9, When I power off and start the...

PLEASE HELP! Photos attached show that our color bank A both cyan and magenta are no longer firing from the printhead. I just replaced the cyan printhead 3 months ago so I know nothing it wrong with it. We've flushed both printheads we've also sunctioned the tubes to the dampner several times to...

Just started experiencing this issue this morning. When I go to open Versaworks it loads as normal but once it's open and I can see my queue A bank it immediately CRASHES and closes the program. I've shut down my computer and also the printer. I also tried to open the software in an earlier...

Hello, Ok so I just replaced my dampers on my cyan head and ink is now successfully filling the reservoir of the damper which is great! but NOW im getting this crazy magenta band going horizontal and vertically. I've never seen that before. I've done multiple cleanings and it wont go away.. I...

Hi Can someone help me with the next steps to trouble shoot my cyan damper not refilling. I just replaced the cyan with a brand new one because the old one wasnt refilling so I thought maybe it needed to be replaced. I am getting a nozzle check of 1 column firing clean and clear but the other...

ok so I just replaced my cyan printhead 2 months ago and all has been great until now each cleaning I do causes me to get less and less nozzles to fire. To the point now i am getting 1 column of NO cyan ink coming down. Can someone explain the purpose of a dampner and what would cause it to no...

I have done multiple bi directional alignments on my Roland SolJet Printer and the detailed print out looks correct. however when I go to print there is always a stroke of blue or pink outlining my images and texts. How do I get the alignment sharp? I did just recently replace my blue printhead...

Photos attached I am getting blurry prints. Nossle check looks GREAT in my test prints so I think its my calibration or detailed head alignment but I already set my alignments and still prints are blurry how. You can see in my prints the alignments of the colors are off aligned. In the word...

Ok so when conducting a test print my dark cyan A bank showed missing nossles in the center of the print. It was causing poor printing so I did some normal cleanings and the clogs seem pretty stubborn. So I did a powerful wash and jut wasted all my ink and still no improvements.Next I tried a...

First time experiencing the clogged head. I've done 3 normal cleaning, 1 medium cleaning and 1 powerful cleaning and the blue cyan A ink section is not printing a full test print. Does anyone have a good link to a youtube video on how to clean a clogged printhead or what I should do in this...

I don't want to print the entire tile of a wall mural. I need to just print a small section to make sure the section is sharp and not pixilated. Does anyone know how to print just a small specific section of the tile and not print the whole thing? I am using Versaworks with my Roland printer

I don't know why but all of a sudden my Roland XC-540 is now reporting a disconnect issue. The printer itself is fine. It's showing the set-up is complete and 51 inches to print on. But versa works is saying status "Not connected" When I click verify my network settings it says "device not...

I am currently managing my orders in PayPal which is a total disaster when trying to keep records of customer information and records, sales, and inventory can someone recommend a good software that will allow me to manage my sign and screen printig business from?

I am printing a large scal graphic on my roland XC 540 printer and before I print the entire graphic I want to sample a certain section so I can see if the color spot color I chose will print correctly. How Do i select just that portion to print?

So I am trying to countour cut my stickers on 3m sticky backing vinyl. The blade is visually out to the size of a credit card and the blade force on the printer I've continued to UP and UP to now Im at 200g force. But still I am not making a deep enough cut in the vinyl. What other functions...