Search results

I've seen this suggestion as well and we've tried it. For our most unruly pieces it's not effective enough -- we run a lot of parts that are multiple times laminated and have a strong bow in them so a full gasket is required. It's not so much that I'm trying to increase speed / efficiency, but...

Hey y'all -- wondering if anyone has any unique tips for getting a good gasket on contour cut parts? We print a lot of CNC cut pieces. The more complex the cut, the more time it takes. More frustratingly, with interior corners / curves, it's not infrequent that, if there isn't a perfect gasket...

We've recently gone through a whole slew of white ink issues on our 360, including this. Over the past few months we've replaced almost every part between the white ink bag coupler through to the white ink print heads. This symptom never went away fully until we replaced our heads. That being...

To parrot White Haus, this sounds like one or some of your motor brushes are going bad. I've experienced the same thing with our 360 and replacing the worn brush turned things around immediately. The part number is 3010115615. Let me know if you need any more description on how to access /...

Update : We shutdown the machine, clipped that yellow ink line, and re-attached so it's no longer kinked. Upon restarting the machine I ran a purge and vacuumed the heads, resulting in a Low status for all channels. It now seems that the white ink pump is no longer running. I can't hear it, and...

Thank you both for replying -- I'll try to answer these to the best of my ability. I've been running this machine for almost 4 years. Me and my supervisor (who operated the machine before me) do perform a fair amount of maintenance and service ourselves, but it's limited to what we've previously...

A few weeks back we had a technician come out and replace the ink pouch inlet, along with the white degas module. He verified our meniscus was where it needs to be, also, and checked our ink connections. I don't know if he checked the recirculation valve or not. It seemed like things had...

Hey y'all. I've been having varying degrees of white ink issues on my OCE 360 for months, and wondering if anyone has any insight. The main symptom we see regularly is : white ink dripping from the heads in the morning. This is sometimes a weekly problem, and sometimes a daily problem. A service...

I recently had similar symptoms to this, and, in our case, it was a leak in our white ink line. It took a while to detect, but our leak was near the gantry. The leak was undetectable until we were advised to flush the line completely with a flush kit. Upon putting in a new bag of ink toward the...

almost 5 years later... I'm hoping you could tell me how to locate the 3 way valve, and how you cleaned it? my machine's current symptoms seem to match the ones you described perfectly.

Some of our team is on site to install hundreds of sheets of UV printed Lintec onto glass, and they found that almost every single piece of Lintec has what they describe as 'clear granules' in the adhesive layer, between the backer and the material. They're practically invisible when viewed from...

The Canon tech ultimately could not explain why we weren't able to perform the manual purge and forego the short flush as the bulletin advises. He ultimately advised we use the short flush method. I successfully ran it this morning for each channel and it all went well.

Greetings everyone, We decided to make the changeover from IJC256 to IJC257. The Application Bulletin here seems to indicate that we don't need to perform the "short flush," which is a process managed by the printer. Instead, my understanding is that it just needs to have a "manual...

Damn. So there is a slight improvement in covering fingerprints in optimal conditions, but it's not a magic cure all. Thank you for your help!

That's great, thank you! Our machine is running every day, with no more than 2 days idle generally. Our sales rep was trying to sell us 257 by touting it will cover fingerprints / ghosting from mask and promoters, as opposed to how 256 makes them show awfully. Do you find this to be the case...

Hello everyone! I'm a newcomer to the forums. I've been running an Oce Arizone 360GT for a year and a half. We're considering making the switch from IJC256 to IJC257. The best, and frankly only, real good description I can find of the two is from the Oce bulletin they put out. However, it...

test post