Search results

Any one recognize this? I tried find my font but just cant get it Thanks

any one recognize the font for Drugstore if it actually is one?

Haven't used my printer in a couple of months, Printing fine but reds are now closer to magenta and yellows muted. Printer says all inks and OP have expired? Would this be the cause or no? Flexi 21 - recent update Have not changed any profiles. Thoughts? Comments Appreciated? Have tried...

HP Latex 115 - Flex 21. Printer was idle for several months. Reds are now printing closer to magenta, and Yellow block is muted and light. Technically inks are expired (not used as much as I thought) 1. Could it be the Flexi Update causing problems with the colors? (I am attaching the setup)...

I sually use 751 for basic car lettering etc. Can't get it at the minute. Is 3M 7125 or #M 180mC a good alternative? I should say it will be for cut lettering if that makes a difference.

I ordered a roll of 30 x 10 751c in white from Grimco in Dec and it is still on backorder. Looks like many of the colors are 21-27 days (or almost 4 months). While I was able to get it elsewhere, has anyone else been seeing this or is it just a Grimco thing? Thanks Mark

Need help on he RR and Ranch please and thanks Mark

So - I have a client that wants perf on the inside of a window that we can't practically get to on the outside. We only need something like a 9" x 48" strip (x2) or somewhere around that. I don't want to buy a whole role for something this small. Do any of you print on this and can do it for...

Anyone on the Hammer and Oak? Design? or basic font? Thanks

What are my options for interior mounted perforated film? Client needs to see it but not see in but windows can not be accessed from outside.

Client wants 8 x 12 ft acm sign. So I normally just get 4 x 8 printed from merchant here. They can print to edge. If I layout my design in flexi how do I cut into 3 images for printing and then do we just align the seams after printing? (client will actually be doing the install). I know with...

Looks like a standard font but can't see to find it Thanks

So I have a Flexi subscription and recently upgraded to version 19. Seems ok so far except for one issue The subscription comes with a monthly subscription for 5 downloads from SignElements. Ever since the upgrade I have not been able to login to that site with a "you do not have a valid...

I need to replace a lighted sign panel. Small 20 x 36" panel. what is your go to material and who/where can I get a pre cut panel that size? I am in Missouri if that helps Thanks

Can you identify the font used in this please? I am close but can't quite nail them Thanks

Doing quite a bit of cut vinyl lettering and graphics on a trailer. Intending to use oracal 751. What is your go to transfer tape for this? I have used various tapes in the past for various projects but have never really settled on one. Would love some advice from those that have installed a...

I have a D140 When I take a printed and cut sheet off my latex printer and place it in the cutter it loads the substrate as normal. It always goes right to the back end of the sheet no matter what size the sheet is.. Sometimes if the sheet is not fully straight it will lose an edge and the sheet...

Rough idea of where you would all be at on this. Printed materials 3 sides 5 x 8 trailer. Just ballparks. I know there are a lot of factors - materials, time etc but a range will suffice Thanks in advance

Anyone printing on 751c with latex? Trying to print with latex 115 on some calendered vinyl before trying cat 751c. Having problems when curling of the substrate? How low can I put the curing temp? Can I adjust dryong time? Any suggestions would be grwat. Had no issues with my 1324 on almost...

Got my new printer yesterday. Heavy beast compared to my 1324 Have setup and first few errors i successfully printed some test runs. Quality was good if a little slow with the curing etc. However when I removed the substrate the vinly started to roll itself up from the edges (not the wound...