I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
Do you have any info on adjustment. I set up the capping adjust in the service menu when we did the dampers and cap top however it does look to be a little of centre. Is there a mechanical adjustment that can be made?
Hi,
We have had an ongoing issue with our mimaki cjv150 for over the last 8 month which has now started to get worse. What happens is that it prints fine with no issues. When we turn off the machine and leave it in sleep mode and come to use it again it produces a nozzle check like this. After...
Hi We have a Roland LEC540 running CMYK plus Gloss and White however we do not use the gloss so it gets wasted in the waste tank. Does anyone have any info or guides on swapping the printer to CMYK plus White White as we use white a lot.
I have done this process before on a mimaki however there...
Hi,
We have a lec540 and when we turn the printer off after use it makes a clicking / buzzing noise. The noise seems to be coming from the power unit but I am unsure on if this is normal or not as we have only just purchased it. I can switch the switch or at the back and this stops the noise...
Hi,
We have had the opportunity to purchase a used LEC 540 at a really good price. I have a few questions regarding the printer though which hopefully you guys will be able to give me the answers too.
1. How long do the UV Lamps last? Are they common to fail or are they solid and will last the...
We replaced all 4 of them at the same time. I suppose it could still be a random faulty one from new though. I will check down the lines to see if there is any air. If there is air could this have been introduced since changing the dampers? Also if it was a seal would you see any signs of ink...
To cut a long story short our cjv150 was dripping ink onto the media last week. We replaced the dampers and capot and the problem was resolved. This week we now have cross contamination in the yellow channel. This is present as soon as we turn the machine on after it has been left overnight and...
Hi,
Has anyone ever come across wonky lines on the dot position adjust. Recently our machine has started to print certain patterns with wonky lines (see attached image). It looks like some sort of calibration issue but I cannot understand why it would just start doing this.
Any help would be...
Hi everyone,
We have started to get an ink mist/overspray on our megenta/cyan channel on our cjv150. The machine is nearly 3 years old and is on the original head. It recently had a new pump and captop fitted as well as a wiper. It has not had any dampers yet at all.
Upon inspection of the...
Hi, below is the link to the head I purchased.
https://www.digiprint-supplies.com/en/cjv300-5540-head-assy-without-memory-board-m015372
We used the memory board from the original head. If you need a memory board digiprint supply both options. The link above is for without the memory board. It...
I see so if the station height is correct the cap cannot be under too much pressure as it’s already hit it’s peak. Is there a separate adjustment for the latch.
So basically the station is set to 5mm the cap position is 3mm to the centre of the sliding pin just as it hits the boom peak.
When...
Hi.
To cut a along story short we have refurbished a civ150 and adjusted the station height to 5mm as per the service Manual. The problem is though that when we adjust the cap position the slider should be 3mm per the service manual but ours has to be about 5-6mm before the head locking latch...
I am happy with the quality of the prints I was just concerned as it only seems to be cyan with deflections. I have since replaced the Pump and Captop which hasn't made a difference. I can live with it just strange why cyan only seems to be affected. I cannot see any noticeable damage to the head.
Thank You,
I have left the machine to soak again today and will see how it looks in the morning. I did get it a whip with a lint free cloth the other day which helped a little bit. A part of me thinks its potentially dampers starting to fail. I know there isn't a full colour drop out but its...
Hi I have noticed the cyan nozzles have become slightly deflected and I am wondering if this is something I should be concerned about? The machine is 2 years old and has had the following work on it done
Cap Top Replaced 6 Months Ago
Wiper 2 weeks ago
Pump still on Original never replaced...
Thanks both of
Thanks for this, We have run the machine for a couple of years like it and have always been happy with the quality. I just wasn't sure how solid the print should be. A lot of the colours are solid but some colours like orange and green are slightly grainy. I assumed it was the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.