replacement

See picture attached. I'm getting this error (See image): Printer was doing fine, but then stopped, tubes as changed not long ago. A techie says it's a new Line Sensor (fairly easy replacement he says). What say you guys, is he right? Please help, we cannot afford a large scale repair :(

Are there head replacement kits for Mutoh available? I know I can get the Epson heads but I'm thinking that there must be something tailored to our VJ-1324 that is prepackaged with everything that should be replaced at once. A replacement video would be helpful too. Anyone have experience doing...

Hey guys i have a little trouble trying to log in MSA to change the main board Already got the new board ready. Here is my printer info and what I got Printer Model = VJ-1624 Mainboard Firmware = 3.04 Controller Firmware = 1.24 Downloaded MSM 8.03 Downloaded MSA 4.1.7.0 From This...

I've only replaced or installed the florescent lighting. I've got a customer that we are replacing the guts of an existing 3x5 box sign. I told him I think now would be the time to go to LED Strip lighting since we are having a hard time getting the lights now. What do you recommend for the...

I read the posts on here about the Gerber shocks and how easy they are to replace. But looking at mine, I was wondering how to take them off? Do you have to just pull them off? Is there a trick? I definitely don't want to break anything. I have replacement shocks from Gerber already...

Have found a couple great places for router bits that do not cost $200/bit like the summa ones do but I haven't found anywhere to buy the replacement blades like the heavy duty knife etc... Any suggestions? We have a Summa F1612 Thank you! AL

I've got a UV printer. I need to replace some of the black tubes going to the dampers. I also need the rubber o-rings at the brass fittings. Do you know where to get these? My local small town hardware store doesn't seem to have these.

Hello, Anyone have a print head they are willing to part with or sell? My magenta is giving me trouble. :thankyou:

I have a cjv30-160, and the right black channel is FUBAR. I'm going to replace the head with an original mimaki p/n m007947. Do I need to replace the memory PCB as well? can I reuse the original one? I've read conflicting stories on this, and need to know before I buy a printhead. Any help is...

Hello everyone! This is my first post on this (big!) forum, so be gentle if the thread allready exists somewhere. We own an Roland VersaCam V-540i since 2009, now it's time to replace the black and blue print heads. We are in doubt over do-it-ourself vs by-dealer. A quick look at both costs can...

Two questions: 1) Where is the best place to buy replacement DX4 print heads? 2) does anyone have a video or step by step procedure for replacing heads on a Roland SC-540? Thanks! David.

Has anyone had one replaced yet? I had one fail on me a few weeks ago and HP replaced it. Now the new one is starting to show the same symptoms. After each carriage pass, the spindle advance has a nasty little 'click' to it that gets bad and then stops and keeps randomly doing that...

Hi !!! So I'm thinking of replacing me black color print head. It hasn't worked for a couple of years and I recently started to clean the lines to see if I could make it work... Long story short got ink to flow to head from cartridge, so I removed the head and soaked it for a couple of days. I...

The warranty's on my Printers have expired. Is it better/cheaper to order parts directly from the manufacturer or through the company i had the warranty with(Nazdar/Sawgrass)? I am looking for mimaki (jv5-320)(jv33)and Roland soljet(Aqueous and solvent) Replacements. Thanks for the help in advance

Hello forum folks, im replacing my sponges in my roland SP-300V and for the life of me i can't remember where the T-sponge goes. it fell out a long time ago and there dosent seem to be any pictures i could find to help as a guide. I know the inside of the machine pretty well, so a brief...

I am installing new print heads in my Roland fj-52. I received my print heads and it seams the the Ranking numbers show different from the existing ones. Was wondering if the Ranking numbers are different from one head to another? This is my first time for head installations, I wanna make...

Hi there, I am looking forward to a replacement Blade holder (blue) for my Graphtec FC7000. Are the cheaper compatible blade holders being sold on ebay recommended? The price difference between these and the original OEM ones is huge. Any one here used a compatible one without any issues ? thnx