Search results

My friend has a graphtec 9000 that he uses for paint protection film and it keeps skipping the left side of the cut. For example if he is cutting a bumper, it will cut the entire bumper except for the left side inside the pinch roller. It does it whether it is a 10" wide or 50" and always does...

Anyone know where I can find a 54" base/stand for my viny express q54" vinyl cutter? I contacted a few places and they said that the model was discontinued and they do not support of sell parts for them anymore. I have the rollers but need the stand/base and the brackets for the rollers. Thanks-

I am getting annoyed with my Seal bas2 62" laminator. It has a very sensitive safety optical eye sensor that is triggered when the vinyl buckles a small amount before feeding into the rollers. I know I read some post earlier about adjusting the eye and possibly removing or unhooking it which I...

Anyone know where I can outsource 6mil. vinyl decals? I found a few sites who screen print them but I need them to be 13"x23". They don't have to be laminated.

I am running a Mimaki jv33 and planning on switching from Triangle MMS ink to Triangle Edx ink. Has anyone ever switched these out without flushing the old ink out? Anyone ever use the Triangle EDX inks in the mimaki?

How do I install the printhead ribbon cables on my jv33? I noticed the factory installed cables have sharp bends in them in order to fit into the space. The new ribbon cables are straight.....do I bend the new ones the same as the factory ribbons? I thought they were very delicate?

I have a customer who wants the panels around his gas pumps wrapped with vinyl. He is having them sandblasted and just wants them wrapped in white vinyl. What would be the best vinyl to use on them and would I have to laminate them since it will not have any printed graphics on them? The...

Does anyone have a copy of cocut software for sale that will work with Vista operating system?

Does anyone know if I can buy just the metal bracket on the bottom of the mimaki jv 33 printhead? I had a bad head strike and it bent the slider bracket really bad. Does anyone have a good used one off of an old printhead I could buy?

I have a mimaki jv33 using rasterlink pro5 sg. I went to print today and got a message across my print that says "not registered". I rebooted everything but it did not change or go away. I read in my rasterlink manual that if this happens then you should uninstall rasterlink then reinstall...

I am using a heavy weight banner for hanging banners in a gymnasium but I am having problems with edges curling. I tried 13oz anticurl banner material and it curled worse than the regular scrim heavy weight material. Does anyone have a solution to preventing them from curling? I cannot hem them...

Did anyone ever use One Shot Graphiguard clear coat? I have always had a lot of success with one shot enamels but never used the clear for digital prints. Does anyone know who sells it?

I have severe ink contamination on my mimaki jv33. Running triangle ecosolvent inks. All cartridges are 50 % or more full. So far I have done the following: new cap top New pump (for mutoh falcon) new dampers Any suggestions as to what to check next?

I have a customer who is looking for 12'x8' or 10'x8' step and repeat backdrop systems that will be used numerous times at charity events. Anyone have a good reputable wholesaler for the stands? Or even the stands and banners as a package deal? Most of the stands I looked at online looked...

I am looking for feedback on mimaki cg 130. I have a mimaki jv33 and 30" graphtec 7000. I have been looking to buy a larger plotter to do some contour print and cut. Just wanted to see what everyone thought about the mimaki plotters. Thanks!

Is it possible to print on canvas with my Mimaki jv33? What brand of canvas works the best? Thanks,

My magenta dropped out completely so I put a new cap top in. The magenta came back full but the damper only has a little bit in the bottom. Is my damper bad? I made sure all of the nuts were tight so it doesn't seem like a air leak. Any thoughts? Should I take a syringe and fill it or do a...

I noticed Advantage Sign supply is carrying the new Triangle eco solvent mimaki jv33 ink for $65 a cartridge. Did anyone try it out yet? I am anxious to hear how it dries, adheres to the vinyl and the odor. I know it just came out a few months ago so its hard to see how it is holding up in...

Did anyone use the Triangle MSS inks in your JV33? How did they hold up? Where did you buy them? How well does it hold up to scratches? I am using Triangle True Solvent inks and they work very well but the fumes are horrible even with venting.

I have a mimaki jv33 that i am running solvent triangle jvv ink. I do a head soak for about 5 minutes every week just to keep everything running smooth. My question is: Is the mild solvent cleaner in the back the same as the flush cleaner? If not can I refill the head soak cleaner cartridge...