#mimaki

Print system On-demand piezo (3 printheads in a staggered configuration) Max print area 98.4” W x 51.1” L (2500 x 1300 mm) Media thickness 1.96 in (50 mm) Print resolutions 300, 450, 600, 900, 1,200dpi Max print speed 376 SqFt/Hr (35 SqM/Hr) / in draft mode Absolute accuracy +/-...

Hello everyone, I’m encountering a problem with my Mimaki UCJV300-160 printer, and I’m hoping someone can offer some advice. The prints are coming out with noticeable banding (waves or alternating lines), even though the test for print heads shows 100% OK, and the media feed test also passes...

I had an issue with my old com16 board had it replaced but then realized that the head was bad also, turn on machine saw light smoke from the print head...cable slight burnt .. so i got a new print head now powered on the machine without head cables connected and the f2 fuse on the com board...

HELP!!! I had a head strike and as a last resort to get the nozzles i lost back i syringed cleaning solution through the print head. I have now recovered the nozzles that i initially lost, but i have now lost all nozzles on the adjoining black nozzle. Any suggestions would be greatly...

Recently i have run into an issue where my jv33 starts printing blurry on straight line edges. Below please see images of the print quality and the head. Do you think I need a new head? Is it normal for a head to look like this? Any advice will be great. I have tried all alignments but it seems...

Hello everyone, I'm David, a technician from Germany. I'm currently facing a challenge with a Mimaki JV150 printer that I hope someone here might be able to help with. Here's the situation: The printer was originally set up with an 8-color CMYK configuration. I flushed all the lines manually...

Hey guys, I have bought a cjv150 with a broken epl2 Board so i bought a new one. It came with epl3 start up fw 1.06 which i upgraded to the newest 1.2. After that i upgraded to the cjv300/cjv150 fw. 4.4 what worked. The machine started as cjv300 and Shows a lot of errors because of thinking...

I've got a CJV150-130 does anyone have instructions on to how to go about chaning the cables in the trailing arm ? i need to change my cables since they are bad.

Evening all - after a paper jam our Mimaki JV33-160 is showing a ’error 43 - y motor overprint : peak´ error message. Does anyone know what that means exactly and what makes it different from the ‘:ave’ error which I’ve found references to? I‘ve swapped the y motor with one from an identical...

Hi folks, I'm new here and looking for some advice. I've been using the Mimaki/Summa combo for several years with Flexi as my rip software. I recently started working out of a different shop that uses Rasterlink 6 and I'm trying to figure out how to contour cut a print/cut on the Summa using...

Need a good icc profile, ones came with raster link, prints alot darker than original print, need something close. Tried those from mimaki not much of a difference. what should i do ?

Hi guys, We're going to be putting our 2020 Mimaki CJV300-160 up for eBay auction next week. Get ready. We need to get it out of the way, so the auction is going to start at $1. Highest bidder takes it. Located in our plant here in Omaha, Nebraska. It has a perfect nozzle pattern and is in...

Hello, I have a Mimaki Cjv150-130. Looking to get a new printer, but only had this printer, so I don't know if I should stick with Mimaki or to another brand printer.

Hello, I'm looking at getting a new printer at the moment I have a CJV150-130 and looking at getting something newer and better. My budget is $20k or less. So many options to choose from, and was looking to get some help from everyone on what machine I should get. It doesn't have to be an...

Lightly used Flatbed Direct-to-Object UV Printer. Model: UJF-6042MKIIE Working Print Area: 23.6" x 16.5" Working Print Height (thickness): 6.02" Ink/Config: LUS120 CMYKWWClPR200 Options: Ionizer & Stand Location: South Central Sometimes circumstances change. Our colleagues and friends are more...

Hi all. We've just bought a JV300 to upgrade from out CJV30. Its currently running CMYKLcLmLkOr but i'd like to convert to Dual CMYK for the speed benefit, as we wont see the benefits of the additional Inks. 1.Am i right in thinking i can just put a small section of ink line to connect the 2...

Hey Everyone! I moved my family and took a different job so looking to sell my shop equipment. Printer may need a new head eventually but everything works well. Looking to get around $10k for it all. Needs to be picked up at zip:15650. -Connor

Full disclosure - main reason for this post is shameless self promotion, however with that said, I do think that this video does a pretty good job of explaining the process of full cut & sew sublimated apparel production, which something we often get a lot of questions about. For a little...

Which printer brand would you say is best overall for locating parts, technician for repairs and online / phone support?

Hello, i have a Mimaki UCJV300-160 and the lamp 1 started giving me temp high error, if I continue printing then the machine gives UV UNIT OVER HEAT error 706 and turns off, I think the blower fan is really dusty and almost no air comes out, but I don’t know how to open it to clean it and can’t...