/ Register

Welcome To Signs101.com: Largest Forum for Signmaking Professionals

Signs101.com: Largest Forum for Signmaking Professionals is the LARGEST online community & discussion forum for professional sign-makers and graphic designers.

 


  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Recent Content by jfiscus

  1. jfiscus
    Profile Post Comment

    Epson inks are expensive per cart, but you don't go through near as much ink as a JV3 does. But,...

    Epson inks are expensive per cart, but you don't go through near as much ink as a JV3 does. But, that also depends on your profiles. I'd say at...
    Profile Post Comment by jfiscus, Jun 4, 2020 at 3:27 PM
  2. jfiscus
    Post

    Frosted Vinyl

    I like the MacTac B-Free Frosted/Dusted, no issues with it using it for around 3 years now. Air release and dry install.
    Post by: jfiscus, May 28, 2020 in forum: Vinyl
  3. jfiscus
    Post

    Changing To Mimaki From Roland

    I'm not sure on your entire range of products, but if you're doing vehicle graphics things aren't flat and the UV doesn't stretch as well as...
    Post by: jfiscus, May 18, 2020 in forum: Mimaki
  4. jfiscus
    Post

    Free Stuff For Y'all

    Finally thinking about wrapping my old canoe. Was kinda tricky to figure out a template, but it had a great straight centerline to measure from.
    Post by: jfiscus, May 15, 2020 in forum: Clipart, Vehicle Templates and Digital Files
  5. jfiscus
    Post

    Changing To Mimaki From Roland

    I suggest looking into the Epson 60600. I've ran Mimaki and Roland also and would not go back. Do not recommend Latex either after our...
    Post by: jfiscus, May 15, 2020 in forum: Mimaki
  6. jfiscus
    Post

    Discussion Stopping the spread of the virus

    I bought a few boxes of cheap Harbor Freight gloves a couple weeks ago and use one every time I pump gas, I put about a half box in each car, and...
    Post by: jfiscus, Mar 18, 2020 in forum: General Chit-Chat
  7. jfiscus
    Post

    Need Help Creating Full Escalator Cling Graphic Template

    Piece of phototex and a grease pencil. Stick it on the panel and trace the outline/shape. Measure a vertical distance and a horizontal distance...
    Post by: jfiscus, Mar 17, 2020 in forum: Dimensional Signs
  8. jfiscus
    Post

    Printing Halftones on Edge 2

    There are tint colors also that are thanslucent, but they'd achieve a similar effect on a fade.
    Post by: jfiscus, Feb 21, 2020 in forum: Gerber
  9. jfiscus
    Post

    Question Is my 360 a lemon, and should I buy another HP?

    If you're happy with your HP's output and just unhappy with the "plasticy" nature of it, then stick with getting a new one of those. When we had...
    Post by: jfiscus, Feb 18, 2020 in forum: Hewlett Packard
  10. jfiscus
    Post

    Need Help 2020 Ford Explorer Door Handle Removal and Reset

    Our installers ran into this also, and if the door is reinforced/armored you're in a real pickle. They haven't found a good solution yet, so we've...
    Post by: jfiscus, Feb 18, 2020 in forum: General Chit-Chat
  11. jfiscus
    Post

    Need Help Suggestions Question Unique Vinyl Project - Glow In The Dark

    We use Gerber GITD vinyl. With it priced as it is, I would do this all as laid up vinyl. More labor, but dang that vinyl is expensive.
    Post by: jfiscus, Feb 17, 2020 in forum: General Signmaking Topics
  12. jfiscus
    Post

    Suggestions Die-cutting low volume magnets

    Yes.
    Post by: jfiscus, Feb 17, 2020 in forum: Tips & Tricks
  13. jfiscus
    Post

    Suggestions Die-cutting low volume magnets

    We print on our Epsons and cut on our Mimaki CG plotters without issue, just be sure the roll isn't too heavy for the plotter to pull it.
    Post by: jfiscus, Feb 13, 2020 in forum: Tips & Tricks
  14. jfiscus
    Post

    3rd party inks killed my head ?

    Everywhere I have worked that used 3rd party inks had issues with heads going bad. Here, we only use OEM inks (now OEM/MCS inks) and have never...
    Post by: jfiscus, Feb 4, 2020 in forum: Roland
  15. jfiscus
    Post

    Need Help GFP 263c laminator Issue

    Looks like too much pressure to me also.
    Post by: jfiscus, Feb 3, 2020 in forum: Laminators

 


Loading...