Search results

Every test print looks almost exactly the same nozzle for nozzle.

Black ink isn't printing properly, but the other colors are fine. Attached is a pic of the test print, as well as an actual print. I've did a head soak, multiple cleanings and cleaned the encoder strip, but nothing changes it. Any help would be appreciated. Thanks in Advance, Paul

I have received what I needed, Thanks.

Having a look, I see that the Magenta sub tank is too thin.

On my VJ 1604, when I go to print a nozzle check (or anything else), a message comes up filling sub tanks, and after some time this error message comes on and all the lights start flashing. Someone know how to correct this? Thanks in advance, Paul

Hi, I'd really appreciate an email with the Mutoh 1604 Tech Manual also. Thanks in advance, Paul paul@max-image.ca

Mutoh ValueJet 1604 I have a 1604 with Onyx PosterShop software for $11,000. 519-424-7000

Installed a new print head. It's printing fine now.

Problem solve with a small fuse on the main board!

I had a little issue. I ordered the print head for my 1604, and it turns out that my machine uses the newer print head that is used on the 1614. So I've now ordered the correct one, and hope to have it on sometime next week. Don't know if you've dealt with MacMedia before. That's who...

I ordered a print head for my 1604. The print head came looking very similiar, but the manifold is thicker. I sent them a picture to show the difference, and they said that mine looks like a 1614 print head. However, they said that I could swap manifolds and it'd work in my machine. Does this...

Chris, When I first had it all back together, I received a cable error. I put the old cables back on (with the right bends, so the cable ends were at the correct locations). Then it showed the "E085Err Head Heat" error. I put my old print head back on... no errors. Now I'm not sure if I...

Big ooops! That is exactly what I did. I had also purchased new cables, and didn't put the correct bends in them, and I got them on in reverse. In doing this mistake, does anyone have experience to know exactly what damage this causes? If it's the main board, can it be repaired? Thanks...

I just replaced the print head and turned on the printer. It initilized and then the the lights start flashing and it shows an error message. E085Err Head Heat Anyone have an idea on this one?

I took the magenta sensor off, and took it apart. It is stopping the ink from coming into the sub tank from the cartridge. It's not plugged, I can see that its function is to open and close ink flow. Does the printer need to be turned on to allow ink flow? If so, I just need to find a...

I'm wondering if this part may be my problem? See pic. What are these, and what do they do? I can push and pull air into the sub tank from the tube that goes to the dampers, but if I keep pulling with the syringe, it flattens the sub tank without pulling ink. I've also removed the tube on...

I haven't yet, but I'll let you know as soon as it's fixed. I've purchused a new print head and while working on installing it, I found out that my magenta ink supply line between the cartridge and the sub tank is blocked. So possibly that is my problem (that it was just starting to block).

Looks like that may be a little tricky to see, but I'll work on it. I took the line off of the cartridge needle and tried to push in with the syringe, but that doesn't work either. If the sub tank is collapsed, can I fix it? Or do I need a new one? Thanks very much for your help.

I've been having a print issue, so decided to install a new print head, dampers, pump and capping station. I pulled ink through the dampers for 3 of the colors, but magenta isn't working. To get a good seal, I disconnected the Y where the ink branches off to go to each damper, and connected...

SC, I just had my pump apart on my 1604, and it worked well. I flipped the tubes around so there's now fresh tubing in the pump. The hardest thing is just remembering how everything goes back together. You may want to snap some pictures as you take it apart. Have you tried filling...