Search results

Yep, the graphic designer is protecting his hard work by only providing you with a low res proof, as a retired graphic designer, I do the same thing. I could re-produce the artwork, but you would not want to pay me for my time it would take. Every graident would needs to be created, taking many...

How do you ship large color digitally printed and laminated hood graphics with application tape applied to the front side? I was told to roll up the print with the image side facing out and ship it in a large long tube or box, however, when I rolled up the print the application tape buckled and...

You use that paper corner rounder to cut 3mm MaxMetal (ACM) sign panels? I have the Lasco corner rounder, but only use it for paper products. I don't think it will cut through 3mm ACM (MaxMetal) sign blanks.

I have a panel saw to cut MaxMetal (ACM) sign panels, however I want to use a hand router and a radius template to cut the corners with a 1" radius. What kind/type of top bearing router bit should I use? I have done this on wood, but never on a Aluminum sign panel, so I am looking for help or...

The reason you can't find the font is because it has been heavily modified. The font is A&S Rhino that has been stretched 200% and sheared 30%. My example below shows the original word "Farm" and then the modified "Farm" to prove my case.

Does anyone know if the white surface coating on MaxMetal is Polymer and will accept Sublimation?

No problem with the old post, I have not made the switch from Win 7 to Win 10 yet, I still need to do it because my old Dell PC running on Win 7 is starting to show signs of end of life. You are correct VW 6 will not work with my Roland SP540V printer, although I purchased it back in 2010, I am...

I don't know the answer, however I recently purchased a used Seal 62 Base laminator and it will not run, I was told that there should have been a plastic pouch on the inside of the left or right removable panel with the wiring diagram in the pouch. Does your Seal 62 Base laminator have the...

Do you have a copy of the Seal Base54 service manual? I just purchased a used Seal Base54 and need to get my hands on the electrical schematic and a copy of the service manual. Thanks

Were you ever able to find a copy of the Seal Base54 service manual? I just purchased a used Seal Base54 and need to get my hands on the electrical schematic nd service manual.

Hi Neil, were you ever able to find a copy of the Seal Base54 service manual? I just purchased a used Seal Base54 and need to get my hands on the electrical schematic nd service manual.

Ok, I would love to chat with Bill, however, you did not PM me his number.... Please send Thanks

Does anyone have a Seal 54 or 62 Base Laminator?

Did you ever figure out what was causing your top roller to heat up immediately regardless of switch position? Thanks

Hi Dan, Did you get your Seal 62 Base laminator working? What did you end up doing? I have one and it will not work at all, thinking it may be the sensor.

Jim, you were 100% correct, I replaced the M/Y head and my SP540V is printing great again. I also pulled (flushed) cleaning fluid through all 4 ink lines and installed 4 new dampers. Thank you!

Jim, here you go. It took me a while to get into the Service Mode, 3 photos of the test pattern fill (right, middle, and left side), and the test print made right after. The blotchy print is because I am using an very old 54" wide roll of 3165 vinyl, however the magenta is showing some...

Jim, ok. Does the fill test use a lot of ink, should I install new carts? Also, if I install new carts for the Fill Test, after that can I put the used carts back in the printer and apply foil tape over the punctured opening on the carts to save for later? In general, what is your advice about...

Hi Jim, I think I have a ink starvation issue with my magenta print head, the nozzle test print looks perfect, however, when printing a larger image with my SP540V, it is printing correctly until the far left side of the image and then the magenta would drop out (you can see it in the gray camo...

Stacey, the window perf is laminated, with Oracal 290F, do you use application tape to apply or go without application tape? Thanks