• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. Review of the Roland LG-640

    Wow....based on that if we print just over half a roll per week day our annual ink cost would be $61,000. Cleaning alone with no printing would be $22,000 a year. That's absolutely insane. We've got a unit on order currently, but we'll be having a very frank discussion in the new year with Roland.
  2. Review of the Roland LG-640

    Just to confirm, are you saying the printer dumped 370ml into the waste ink bottle in a 26 hour period? Was that amount measured from the drain bottle or calculated from the drain fill % on the display?
  3. ROLAND UV PRIMER ADVICE PLEASE URGENT

    Roland had a decal option listed for the previous generation of UV printers, but it was never widely released. The concept behind it was to print an adhesive layer through the head so you could do UV DTF transfers with the machine. Apparently they couldn't could things working perfectly and...
  4. s80600 owners, leave your machine on or off when not using?

    We have the same issue on our S80600, the high rpm fans keep spinning even in sleep mode.
  5. Need Help Cutting Master 4 - "Duplicated, Convert to Curves, Delete"

    In the end I rolled back our CM4 install to the previous version and it fixed our issue.
  6. Importing Vinyl From China

    Maybe the higher end materials, but there's loads of Arlon manufactured in China.
  7. Will an Epson S80600 fit through a standard interior door width?

    We fit ours through a door that was 31" with no trouble. IIRC there's a section in the manual about how to prep the printer for narrow doors. The heater unit on the front can be loosened and swung down to give clearance. Combining that with removing the front and rear media holders meant it...
  8. Need Help Cutting Master 4 - "Duplicated, Convert to Curves, Delete"

    Fresh installation of CorelDraw 2020 + Cutting Master 4 (Ver. 4.4) on our new production computer and I'm getting some strange behaviour when we launch the registration mark plugin. It's going through every object in the file and doing a "duplicated, covert to curves, delete". Not just on the...
  9. Looking for a cheap laminator just to mount film on rigid board

    Those Qomolangma laminators punch above their weight for the price.
  10. Question New Epson S80600 & Summa Cutter Performance

    You should be hitting 12m^2/h comfortably in 8 Pass mode. Check your rip settings for inter-pass delay etc. Is your network gigabit?
  11. Advice for new Setup (Epson SC-S80600 or Roland TrueVis)

    S80600 100%. Nothing else in that price range comes close on build quality, features and print quality. We've had ours for 2 years and can barely fault it.
  12. Roll to roll UV printer?

    We had one of these on our short list but no white ink was a deal breaker.
  13. Glo in the Dark vinyl

    There's a Japanese material that we've heard good things about - Kiwalite Photoluminescent.
  14. print runs

    Bet you were thankful for the Colorado print speed on those.
  15. Graphtec FC9000 reviews and experience

    It's a balancing act between the two. If you extend your blade too far you'll end up with "feathering" when you cut through the liner, leaving a pretty rough finish. Depending on your customers expectations this may be an issue.
  16. Graphtec FC9000 reviews and experience

    FC9000 will read on holographic, the 8600 won't.
  17. Graphtec FC9000 reviews and experience

    We use the regular cut line pattern for all of our work, but we'll switch to the actual perf cut pattern on larger graphics. We run our force at about 30 using Clean Cut blades, although this is going to vary based on the media/laminate.
  18. Can I shake cartridges before turning on printer?

    Hmmm curious. When you let your S80600's go to "sleep" does it actually go into a full sleep mode? Our just turns off the display after 15 minutes, but the blue light stays on solid and the fan continues to spin and whine forever.
Top