• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

cjv150

  1. Mimaki CJV150-75 Missing Nozzles and printing fuzzy with overspray

    Hello, I'm fairly new to wide format printing. I purchased a Mimaki CJV150-75 in '22 to be able to print marketing materials in-house (stickers, banners, posters, etc). I don't print every day, but I do at a minimum run test prints everyday to make sure everything is in working order. About...
  2. Mimaki CJV150 - preheating don´t STOP - always heats up, even in standbuy

    Hey guys, a Mimaki from one of my clients did not stop heating. The Heater is already turned off totaly in the Menu and the machine is also heating in the standbuy menu. So he and me are scared of to much heat as it is heating up until 76 degree... so he needs to turn of his machine and is not...
  3. Mimaki CJV150 splashes ink around capping station when cleaning

    I bought a second hand Mimaki CJV150-160BS almost new with a fried motherboard that I fixed. The printer came with a lot of disassembled parts, all in a cardboard box and I am not sure if I did get them all. When the printhead gets cleaned the rubber squeegee splashes ink everywhere around the...
  4. Mimaki CJV150 printing grainy/faded

    I have a Mimaki CJV150 which had a new printhead installed last year. Has been working fine up to about a week ago. The Test print shows that all nozzles are perfectly fine but the print comes out very grainy. Has anyone got any tips?
  5. Mimaki cap adjustment help

    Hi. To cut a along story short we have refurbished a civ150 and adjusted the station height to 5mm as per the service Manual. The problem is though that when we adjust the cap position the slider should be 3mm per the service manual but ours has to be about 5-6mm before the head locking latch...
  6. Mimaki Deflected Cyan Nozzles CJV150

    Hi I have noticed the cyan nozzles have become slightly deflected and I am wondering if this is something I should be concerned about? The machine is 2 years old and has had the following work on it done Cap Top Replaced 6 Months Ago Wiper 2 weeks ago Pump still on Original never replaced...
  7. nozzle check help

    Hi everyone. Could someone please clarify why if we print a nozzle check in the morning once the machine has been left its blurry / fuzzy but if we do one after printer its clear. Please see attached photos Thank You
  8. Mimaki CJV150 station height and cap adjustment help

    I was just wondering if anyone could give me some advice regarding the cap top adjustment. In the service manual it states the pin which runs up and down the track taking the cap top up and down should be 3mm to the centre from the highest point. On our machine if I adjust it to what is stated...
  9. CJV150 Print Head Replacement

    Hi, Recently we picked up a Mimaki CJV150 cheap as it had been sat unused for a few years. We are hoping to get it up and running without the need of a tech. I have a few questions which I would appreciate help on. The machine had been left on however the ink had expired and the cap top was...
  10. Need Help Y Belt problem in Mimaki CJV150-160

    Hello everybody, We have a problem on our Mimaki CJV150-160 machine. the Y belt does not have a direct line, it goes up the side of the pulley when the carriage is running. you would have a clearer explanation by looking at the pictures. kindly please help me solve the problem.
  11. Need Help printing problem CJV150

    Hello, for three days I have had the same problem. I tried all the cleaning modes as well as the nozzles wash for 5 and 20 minutes. I also noticed an incorrect alignment on the MAGENTA. Please help me. Mimaki CJV150-160
  12. Need Help Cjv150 System Halt (2) 509

    Hello, we have a CJV150-160, this morning after detection the media, the head stop in front of the sensor and this message appears : " System Halt (2) 509 : HDC POSCNT " Can you help us please. thank you.
  13. Need Help Mimaki CJV150-130 - "INK TYPE" error

    Hello. I use a Mimaki CJV150-130 in my work. In my work we use this machine to do some signs, only for the company purpose. So we buy new INK cartridges, in this case we buy SS21 ink, but we previously use BS4 ink, and now when we try to put the machine running appears an error in the boot "INK...
  14. Mimaki CJV150-75 or Roland VS-300 for the same price?

    Which one is the better deal? What are the main differences between the 2 in terms of tech.
  15. Need Help Mimaki Dryer damaging Vinyl?

    Hello all. First let me say that I am not only new to the forum but to the process of Print/Cut Vinyl. We are running a Mimaki CJV 150-75 along with Rasterlink 6 V5.15 and Finecut 8. I have had no proper training on this machine and have been figuring it out as I go. I have managed to set up a...
  16. Need icc profiles - Mimaki cjv150

    Hi Was wondering if someone had icc profiles for CJV150-160. ink conf. is ss21 - CYMK, Rip is Rasterlink6. Thanks
Top