Recent content by alevye

Hello. Good day. We are having this same problem after we replaced a Servo Board on a VS-640i. The problem with the old Servo Board was that was not operating the Solenoid for the Cutting Tool. We set the new Servo Board and got the message: "PRESS THE POWER KEY TO CLEAN". We powered on and got...

Hello. Good day. We are having this same problem after we replaced a Servo Board on a VS-640i. The problem with the old Servo Board was that was not operating the Solenoid for the Cutting Tool. We set the new Servo Board and got the message: "PRESS THE POWER KEY TO CLEAN". We powered on and got...

I am a Field Service Engineer with more than 25 years of experience in all kind of equipment in this market.

Hello. Need some help. I have been building a new profile for my PosterShop 12 for UV printer. I did all the steps until reading the swatchs for ICC profile. Then my "Build ICC Profile" is not available... Can someone help? Thanks please

Hello... Good day... I lost all my manuals with the ransomware Cerber 3, so if you can send me please the VJ-1624 service manual will help me a lot.. Thanks in advance... to alevye@yahoo.com

Hello. Somebody help. We have Error 076 Pre Heat. According with the Service Manual it says that must check the connections in the Thermistor or Heater on both sides (Heater and the Board). We checked that. Also says to replace the Main Board. Done that. We have 3 VJ-1614. Two working and one...

Strange banding intermittent FJ-740 Hello. Please, check two things in this case: 1) I think that you have to increase your step calibration with this media. Do it using MENU -> CALIBRATION -> SETTING Try to increase it until you have better result 2) Check and try to use another media...

SP-540 Quits printing black Hello. One question: when you do the syringe reprime or pull ink from the cap using a syringe, did you see air in the syringe or hear some air in the Print Head - Cap area? If so, you can have problem with 3 things: Cap, Damper or Head Manifold First test I would do...

JV33 Bad Quality printing after installing head Hello. In JV33 is really important to proceed with several adjustments after replacing a Print Head: 1) First, you have to do a HEAD SLANT Adjust in Technical Mode. This is really important because affects the Print Quality a lot. You will need...

SC-540 vertical lines problem Hello. If after cleaning the encoder strip and the encoder sensor won't fix your problem, then the problem is one of the FFC or Flat Cables between the PrintHead Board and the Mainboard. One of them is getting a disconnection every time the Carriage gets to that...

SP-540v Turn On Power Again problem Hello. After you tried removing the battering (before of the unplug the machine from power and wait to 2 - 3 mins) don't solve your problem, you can try other things like: 1) Try to change the room conditions (like humidity and temperature) and check again...

Sc-540 Hello Tom. How are you? I don't have exactly the manual for SC-540, but I have for SC-545 that are really similar, in any case that will help you Here is the link https://www.dropbox.com/s/2pkq8tz4w6h81fk/servicemanual_sc545.pdf Thanks Regards

Hello. Yes, I have bought from Digiprint-Supplies and they are good and quick and also there is this website www.sign-in-china.com http://www.sign-in-china.com/products/6187/Roland_Eco_Solvent_Printhead_DX7_6701409010.html Also serious and quick Regards

Hello. I writing to present a case I have with a customer to get some help. The printer at issue is a XJ-740 and the problem is as follow: Using a media of 1.23 mts wide or less and with the Vacuum Power set at AUTO (as default), when sending a job from Versaworks, the Vacuum in the printing...

Hello. I recommend you this syringes. They are a really good price. http://www.sign-in-china.com/products/3913/All_glass_syringe.html Regards