Search results

Hi, Help please :) I have a Mimaki CJV30-60 with 4 Colour CMYK Eco Solvent SM3 Inks. I would like to change the Ink Type to 4 Colour CMYK SS21 Inks. Is there a Process I need to do as if I just put the SS21 ink into the Printer, the light stays RED and does not Change to GREEN. Thanks.

Ok, so I bought a new Junction board, installed it and no change, still coming up with Broken Chip Error or S/C ReadErr. I replaced the Chip Readers from a working Mutoh all checked and no pins bent etc. When I install genuine OEM Inks they show Ink End as there is no ink in them but just to...

I still have this issue :( I have checked the Ink ID Boards as Picture above and they all seem fine, no broken pins. When I put OEM inks in I get the KCMY Broken Chip Error but when I put Compatible inks in I get KCMY S/C Readerr. I have also tried both the ink types in my other printer which is...

Hi, I have an Error on my Mutoh Valuejet 1324 of [KCMY] Broken Chip and will not let me get past this error. I have tried the inks in my Valuejet 1304 and they work fine. Help Please :) Thanks.

Hi, I have a Mimaki CG-130 FX II and I downloaded the Mimaki Driver for Windows 10 64bit all seemed to install ok on my PC as I checked the Device Manager. When I switch to REMOTE on the Cutter and then send the image to be cut from my Wasatch RIP I get a Current Device Not Found! errorcode=5...

Found it :) Brilliant, Thank You! It was the Summa S series with OPOS Cam Manual I needed.

Hi, Can anyone point me in the right direction where I can find a User Manual for a Gerber P2c 1400SC Plotter. Thank You :)

Brilliant :) The Summa Drivers work a treat. Thank You!

Gerber P2C 1440S Driver Hi, Thanks for this but it does not seem to install with this driver. The Cutter is a P2C 1400S.

Hi, Can anyone point me in the right direction to find drivers for Windows 7, 8 and 10 for a Gerber P2C14005 Cutter. Thank You!

Hi, I have an XC-540 which has 6 heads and takes 12 Inks, 4 of them being White. 1. Can the machine be converted back to be a CMYK LC LM? 2. If not using the White Ink Channels, what is the best way to close these up without drying up the heads? 3. On printing colour images which do not contain...

Service Manual for Soljet 3 XC-540 Hi, If you have the service manual for a Roland Soljet III XC-540 can you email it me please at steve@belmonte.co.uk. Thanks :)

Default IP Given to Roland when Reset Hi, Thanks for your reply :) The Print & Cut is an SP-540V so I do need the net-tool. Can you tell me what the default IP address is after doing the reset of the network card? I think I may need to set me Laptop to this range when using the net-tool...

Hi, I have checked all the menus and cannot find where to set the IP Address for my SP-540. I have also run the Roland InterCon-NetTool to see if it would pick it up but nothing. Is there a way to find what the IP Address is set to on my SP-540. Thanks.

Issue Resolved - Bad Head I managed to resolve this as it was down to a bad print head. :)

Resolved - It was a Profile Issue Thanks For Your Help. It was indeed down to the Onyx RIP Profile after all as the CMYK Print from the Mutoh was 100% fine. :)

Hi, When doing a test print or any other print I just get Magenta Streaks. I have ink to each of the 4 printheads as I have drawn it through from the Waste side - other side of the caps. See Image, sorry for the orientation as it should be 90 degree right: Thanks :)

Hi, Can you help as I am trying to print gradients of Black which have a green tint and Gray seem to print Brown. I am using Metamrk Media. I have a Mutoh Valuejet 1304 and using Onyx RIP Center Mutoh Edition 10.0.0.89. Thanks.

Gradients of Black Wayne, I am using Metamark Media and trying to print Gray. Basically when printing 100% Black is fine but it is the Gradient colours leading upto the Black have a green tint and I cannot get the Gray colour. As when I print Gray it tends to be Brown. I am using Onyx RIP. Thanks.

Resolved IP Address Missing Menu Thanks Guys :) It was indeed in the Menu5 > Menu Option and Select #23 to enable This is with FW 1.07