Search results

Alright I see. Then I will try to locate Artisitc digitizer, or digitizer pro by Janome. Just curious as If I can use this machine with out my RCS sceen. thanks for your input

Janome mb4 was given to me but the Rcs screen will not turn on. Stopped working after update was told. I see that to operate the machine the Rcs screen is optional. manual says a computer can be used. Im unable to find a screen to purchase so wondering what kind of software will it need to run...

@ umca and Netsol without removing the transistors do these readings say anything? Or must I remove them all? Meter on diode. On hFE setting I get nothing. Also, my F4 fuse has erratic reading then ends at overloaded, rectangular beige fuse. F1 and F6 are identical fuses they are stable continuity.

I have some knowledge on electronic component testing. But not much with transistors. Will a multi meter suffice? Or will I need a oscillating signal generator tester? Can I get accurate readings with components still attached to the board using a hand held meter. Or must they be removed

honestly I do recall few drops of ink falling from damper on my head board. I just wiped it. I did clean it with alcohol second time around but Im afraid the damage might have been done already. I also installed new ribbon cables. So, most likely transistors then. Thanks for reply I can now do...

alright so focus on the main board then. Wasn't sure if I should check CR board or main board. Ill check the transistors. Thank you

i have same problem. mine was printing good until I replaced single damper. Now it will not lay down ink. Station is pulling ink. I replaced head cables and fuses no luck. Then I replaced new head, with new fuses again and it keeps blowing my F3 fuse on main board. 750 ma. Should I focus on CR...

if anybody can help Im out of ideas. Converted 1624 to dye sub ink. Did a very thorough flush. Lines are very clean. Install new dampers, M station and foil ink bags. Turn unit on all lines are pulling ink except one magenta. Did nozzle check and it is very good aside from that single magenta...

hey Yes , I have decent knowledge of it. I checked all the fuses on the main board and they all good. I have 120 volts coming to printer and main fuse. Main fuse is ok too. The first cable connector to power board is providing 120 volts. But onward of power board is my issue I think. On the...

No air bubbles. The one cayan channel is perfect. The other I cannot get it to work. Bunch of cleans and it comes back fully but then drops out again. I’d like to rule out ink as I’m on a new bottle of ink, new batch. I dunno!

It’s been a busy month with issues can’t seem to get on track. I dropped the front cover on my rj900x and the power went out. Cannot turn machine on anymore. I unplugged it over night and still nothing, as awhile back had a similar incident with losing power but was able to restart after...

ok nevermind I figured it out. When I select different wave effect that uses different head channels and disengages the plugged cayan channel it no longer sprays or contaminated the paper. In wave effect you have the option to select A channels, or B channels. of the head. Since one of my Cayan...

is my print head toast or something else going on but my prints have bleeding or ink migration past the edge of the print. As if fine dust of ink is falling or spraying the paper where there is no art. Its ruining all my prints. First I thought it was pressing issue but after inspecting the...

I flushed my cayan entire line with di water. Cleaner my cartridge entirely. Poured in new ink bottle of cayan. Installed yet another set of dampers. Had to do about 7-8 cleans and finally got my cayan channel back fully. Did several nozzle checks and prints and channel was good. Printer sat for...

I think you are right! It slipped my mind that few years ago my Cayan ink turned into a jelly substance. I then realized the bottle they sold me was expired. Yes, sublimation ink. I'm using Kiian ink. Only If I could charge or flush a single channel. Thanks

Anybody try (oil, electric) Drum roll to roll press? Cut and sew high volume print plus press. Looking to buy one but have never seen one in action. Are transfers good quality? My flatbed presses are from China and still functioning after 10 years so was going to look there as I see them ranging...

Im battling with my Mutoh rj900x and cannot seem to find solution. I keep losing 1 channel of Cayan during print. If Im lucky I may get hour of both cayan but eventually will drop out. Entire channel. Do a handful of cleans and I get it back. Then During print it drops. Then I get it back and...

Im looking at a jv30-130 to convert to dye sub. Was told it does not use expiry chips...Will use BIS ink set up. Ive never owned a Mimaki only Mutohs and have a question if anybody can answer before I purchase. Must you use all 8 carts? Can only 4 be inserted CMYK? If all 8 are inserted how does...

all my inks are dye sub. I have stations that have lasted 3-4 years but I also have some that fail a year in. Have 2 handfuls if these things sitting around. I ordered some tubing just hope its correct diameter.

I have a contact who does this for me remotely. 10-15 mins job. Then I use bulk system. We are cut and sew so i need lots of ink.