Search results

the site has sucked, FOR OVER A YEAR NOW. the ads aren't unmanageable on my ipads, but, the older one keeps pestering me to load thatbstupid tap a talk app. it doesn't load right, AND THERE IS NO, SAYING "NO" when i use my surface tablets, you can barely locate site content, between all the ads...

you say you soldthe main board...

I have very little experience with onyx, but, MANY TIMES, with other software, it has been as simple as locating the text file or xml that lists models that will work and adding your model, with a text editor, following the formatting the software developers used.

hopefully just cables, although i have had 2 different heads on my sc545-ex go bad that way

check/change ribbon cables BE CAREFUL. fully power down, unplug machine WAIT 15 minutes for capacitors to discharge lets not turn this into blown fuse/shorted transistors i think any time you disconnect a ribbon cable to check it, you might as well replace it we had an issue on my sc545-ex...

carefully clean encoder strip with isopropyl alcohol do a really good head soak, at least overnight, take a syringe and flush alcohol or flush through the pumps and line leading to the, as well as to drain bottle uou will probablynrnd up buying new heads, though

grants are generally money the government will give you to pursue a course of action that no one with a half a working brain would otherwise choose congress loves to engage in "social engineering" & and if only they were capable of making an intelligent decision themselves, this system might...

ed from inkjetperformance.com in georgia MAY have a board they also offer repair service you can also serch for roland board repair on ebay, but, there is a risk, sending off your main board, you may never see it again

but you don't have the board that most likely is causing the problem

hardware stores & auto parts stores have suppliers that sell "assortments" (for them, not for us) i have a piece of steelshelving that is covered in assortments c-clips, e-clips, snap rings, etc. hollow wall anchors, electrical connectors, grommets, caps & plugs whenever i make a trip to the...

we have a real dust collection system. how can that rigid shop vac suck anything up through 20' of 1-1/2" pvc? they barely pick up from a 6' hose.

i used to have a car mechanic friend. in 1980 he yelled at me because i hung a wrench up. it wasn't facing the same way as all the others. stopped him dead in his tracks... reminds me a lot of this guy. that application table is something, though...

very impressive!

i kind of assume the "free estimate" is part of customer acquisition cost having been on the other side of transactions, i have never paid a site survey fee, (of course i am talking about initial visit, not something requiring engineering drawings, etc) i have done plenty of surveys over the...

But that is the nature of tech. At one time we paid $500 for a Texas Instruments calculator. 20 years later you get it at a 99 cent store I n 1978 we had people coming from Ohio to NJ to get vcr's projection TV's and the camcorders serviced. (the ones ABC used to cover the 19760olympics) 1987...

you may need to wait till all the fuses are in. i would think the startup pulses the motor,, moving a fraction of an inch & looks for a pulse from some sort of sensor with a wheel

you are not really giving enough information does the media advance when you press the arrows? does it make an odd noise? does the error come up every time? i get that error if i reach end of roll & am not paying attention i assume you are powered up, media loaded, have setup medial when you...

wrong value fuse CAN NOT give you a feed motor error. i would agree the printbis odd. is there ink spilled on any of the ribbon cables? ink is conductive & dissolves the white, insulatiion, can cause a short also look at carriage board for ink, are you sure a conductor on the ribbon cable did...

bill, if you could send that to me as well, i would really appreciate it

lets start at the beginning why did you replace the old head? what was it doing? where did you buy the new head? in what way was the nozzle check "odd". ?