Search results

Yes and no. Mutoh has aqueous and eco-sol versions of most models. While the parts might fit, running eco-sol through an aqueous printer will cause damage since the parts are not meant to come in contact with solvents. Then there is the issue of smart cards. An aqueous printer won’t accept cards...

The only difference in the nozzle check should be the addition of the date/time etc. I would do a cold reboot (power off- unplug- press power to drain- then restart), and/or reload the firmware. Also 3.05 and up does not allow 440s on a 1324. Your ink choices are 220s or 1000 ml bulk

Try this preset in the link: https://fellersinc-my.sharepoint.com/:u:/g/personal/scott_steinecke_fellers_com/EUfjS4XycKFAnd_tfJr1vOEBeSKnbaXaQoWp6Gtj_FlwwQ?e=QO4r9M

Do you buy any supplies from Fellers? If so, call our Equipment Support line Monday and I can remote in and get you fixed up. 888-863-8383 ext 3120. Ask for Scott

What version of Flexi are you running?

How does your nozzle check look?

Normal. On the XPJ 64” printers, they added brackets to reduce that effect.

Check your messages

The only factory authorized method of turning off the smart cards to to retrieve an MPI file from your printer using an app called MSA. We then send the MPI to Mutoh and they generate a ULK file, which we reinstall with MSA. It disables the readers for an allocated amount of time. Since Mutoh no...

To further clarify: Mutoh VJ-1324/1324X with anything over firmware 3.02 cannot run 440ml cartridges. This is, in fact, because the cartridges are in the printer horizontally and 440s will not properly drain. Anyone with a Mutoh VJ-1324 or 1324X can use the 1000ml bag adapters. Broken chip...

Any firmware after 3.02 will not allow 440’s. 220’s and 1000ml only

Mutoh reports that there is a bad batch of subtanks out there that collapse and will not refill. This issue is for 1641/1682 SRPros only. However, it's possible that could be an issue with an older machine too. Normally, replacing the ink valve should be sufficient unless there is a kinked line...

Push on the valve actuator so it opens up and push cleaner through the adapter from the end that goes into the printer. It should come out of the needle that pierces the ink bag. Be sure to order some new plugs because you don’t know how long they have been in it and can leak if they are old

Not because of cross contamination. Nozzles missing means you need a head if they won’t recover from cleanings. Don’t clean with Little Charge or Inital Charge. Ifn fact 2 smalls works better than one long cleaning

https://drive.google.com/file/d/1vMbzXhMrLzv-k9ZphwmVnookYXB0-wiH/view?usp=sharing

Here ya go...https://drive.google.com/file/d/1vMbzXhMrLzv-k9ZphwmVnookYXB0-wiH/view?usp=sharing

Cut server requires a Google Drive link. https://drive.google.com/drive/folders/1-Wk9MPF8Kjf2cgTbUNpWl6QtAlbn9msr?usp=sharing

Try these

Mutoh no longer supports the Kona. It’s possible that the file is on the Mutoh Europe site, since that is where the Lona cutter was sourced from in the first place. Meanwhile, I’ll check the dealer FTP.

From the rear media sensor to the edge of the home side ( left from the back) media spool. The rear media sensor hole is an oval shaped hole between 2 pinch rolllers. You can see the hole from the back. I’m thinking close to 18”-24” is the minimum.