Search results

Just curious Ashley348 di you figure out the issue? I am having the same issue that I think is called silvering. Almost a metallic look after laminating.

I’m also having the same issue. So you selected the hard disk erase? Like everyone else I’m nervous about selecting that option

Old thread but I’d figure I’d add my name to the list of people getting bad 8518. Last 10 feet of so on the roll is all blotchy. Basically useless.

Yikes, It was so clean i didn't even notice it. If maybe there was a little cyan showing it would have seen it! I replaced this am and its 90% there. Still some slight banding after head cleanings and alignments. Just odd how brand new printheads still show some bad nozzles in the service...

Not sure why but certain colors have developed a banding issue. I did the nozzle check plot and replaced 2 heads although they weren't really bad. Aligned heads and tests plots seem fine. Cleaned mulriple times. This may have started after replacing the cyan cartridge last week. Could it be a...

I have the spares but they just get glued up too. I clean them off but within a few feet they are cruddy.

Had this issue on another printer as well but the right side edge of wrap vinyl has some adhesive exposed. The first roller gets gobbed up with and and wants to pull the wrap up. I'm using the edge holder but if I don't feed extra vinyl to start it will get crumpled there. Can that roller be...

So I went back and looked through emails. yes I had to send a file from the printer to get a file back to upload to the printer. Basically the carts always look full until the manual flag on the cart gets tripped. You can put any cart in any slot including cleaning carts and it doesn't care...

I have a used VJ-1324 that has been unlocked. Basically want it gone. Maybe the boards will work with your printer?

It has no problems with smaller files. Also I usually can resend the problem file and it cuts fine the 2nd time around but a few parts are already fubar from the first attempt. Not sure if the file it too big but I can see that.

Contour cutting a 48" x 108" layout. It goes through and finds all the registration marks fine. Then for some reason starts cutting 2" out like it scaled the file smaller? Doesn't always happen, usually I try same file again and it's fine. Using gosign that it came with.

I have a VJ-1324 printer that hasn't been used in a few years. Was flushed after last use. Has a take up reel and flashed to use chipless carts. Found out the hard way that solvent printing wasn't for me as I just didn't use it enough and more ink was used running cleaning cycles than...

Thanks henryp for the pics. I just cant seem to find those parts anywhere. It also seems like its heated in place. Joe House I did try to clip a small amount off but then it doesn't fit quite right afterwards. You can see on #10 above that there is a slight taper right where it goes in to...

No one? Does this mean I have to get a factory service guy to order factory tubes? Probably cost as much as a new printer!!

So I think I've narrowed down my problem to be with some of the ink supply tubes leaking air where they connect to the dampers on the head. I'm seeing some small air bubbles in the lines. I'd like to replace them but can't seem to find them or how to do it. They have a 90 degree bend in them...

You win. Seem you've been called the forum bully a few times here so i bow to you. I'm gonna go brush up on my file uploading skills now. BTW Look up passive aggressive.

Wow Gino do you work for Flexi? don't take it personally. If you want to compare computer skills I'd be more than happy to take on anything you have, been in the IT field since punch cards. I was told by others that I couldn't post an image directly here and had to host it on another site so...

Ok so I solved my own problem but will post here to maybe help others. So I don't know how but the profiles in Flexi rip and print (3 of them because I tried multiple) all had the color adjustments changed. It's a little odd how it does it also. The first screen has "all colors" selected and...

The images are uploaded to google. One more try. unclebun why is it now printing a transparent black over everything? I've printed this fine many times before.