I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes.
Click to Support Signs101 ...
Hey there, I had to change the blade in my summa s2 t160 and I thought I had it tuned in a cutting well, now it is leavings what I would call vinyl shavings in the cut and not cutting corners crisp, I used a clean cut 60 degree blade cutting oracal 651, i have never had this issue before on this...
So, I upgraded to Flexi 21 from 19 and can't figure this out. My print/cuts on Opus and Opus Extra mode for some reason comes out 15/16" off the actual cut path. Flexi Tech support can't even figure it out they blame summa lol?. I upgraded on my cutter the firmware to the latest. Printer is a...
Its...one of those days
I can't figure out why our T160 can't seem to stay in alignment for this small sticker job and hoping someone on here can tell me what I should be doing differently.
I ran 100ft worth of stickers last week without any issues so Im pulling my hair out trying to figure...
Hi, I have a summa D60R and the clamp that holds the blade in place has cracked. I have tried glueing it but refuses to hold the two pieces together. I have been in touch with the dealer here in the UK and they say its not worth repairing as it will cost over £700 to fix it, £400 for the part...
Hi there, at my workplace I use a Summacut D160R to cut things printed with a HP Latex 365 but recently it seems to be getting worse at cutting where it's supposed to.
For example - just did a vinyl print of about 2m length, I had a 10mm bleed on it, but from the start to the end it still...
Hello guys I've been using my Graphtec Ce6000 for almost 7 years now, mostly for print cut and small detail colored vinyl cutting, this machine is built like a tank and ive only changed the blade. I want to upgrade to a newer cutter, had my eyes on the fc9000 and the S2 T (never use a summer...
Hello,
I'm running into an issue with our Summa S2 T series where the OPOS system is unable to read the plotter registration marks. It was working perfectly fine for one job then the next job was having lots of issues. It was printed on 136oz optically clear lam, which made me wonder if it...
Just got our first Summa S one 120. Everything worked great on our regular white vinyl (1 meter width). But then we tried to cut thicker and wider material with UV printing and it was horrible (photo is in attach). We tried everything: new knife, reduce speed, change thru-cut settings - nothing...
Hello everybody
I own a Summa S 120 T cutter and i'm facing a problem after i had to unscrew and lift up the tangential clamp (loosing 4 scews see pict) to remove a tangential blade wich was blocked alone.
After mounting up everything the cutting is not horrible in sawtooth.
Can anyone know...
Hello guys the back plastic part of the pinch roller is sometimes scratching my prints especially visible with dark prints. the paper goes back when cutting creates a high point where it hits the corner edge of the pinch roller. any solutions to this? I put some paper tape and it helped a bit...
Hello guys the summa s2 is not cutting the last part of my mural for some reason not sure why. I have have paneling set to On. The machine before was unrolling my whole roll of media before cutting so the distributor recommended me to turn on paneling and that fixed my problem. but now its not...
Hi guys how do you lower the inner pinch roller pressure on the s2 as its leaving a bit of an indent on my paper the manual only says something about the outer roller but not the inner.
HY
We are interested into buying a FC2250 equivalent flatbed plotter. We would be grateful if any member would send an offer.
Thanks for watching.
Regards
Franck
Hello when im trying to cut a roll on the summa s2 and it always unrolls the whole roll thing before it starts cutting and its making my media crumble up.
So I set the roll up then line it up well and clamp it down and it does the minimum load procedure. after that I click Media Size> Roll > Set...
Hello when im trying to cut a roll on the summa s2 and it always unrolls the whole roll thing before it starts cutting and its making my media crumble up.
So I set the roll up then line it up well and clamp it down and it does the minimum load procedure. after that I click Media Size> Roll > Set...
Hello trying to cut like 15 foot long wall mural on a roll but sometimes the media doesn't fold well in the media catcher and kind of crumbles the print a bit. Is there a solution for this? do i need a take up reel option so it can roll in there. I have a summa s2 t160.
I think i need this...
Hey guys.
I have a Summa s2 160 t and I'm trying to contour and perf cut from SAI.
I have created the contour lines, chosen different colours, have the contour set to Tangential and the perf which is a different colour set to Flexcut Accurate.
The flexcut mode is OFF on the cutter...
Hello new to the machine Im trying to cut 2 long pieces of wall vinyl 24" inches each on a 54" wide roll about 200" long but im having trouble as the paper is going back and forth a lot and falls off the backing and machine gets jammed. I lowered the knife pressure by a lot and and the...
We bought this brand new from the Vegas sign show about 5 years or so ago. There's nothing wrong with it other than it's kind of a PITA. Not a big fan of needing to change foils if you have a lot of colors. About the only saving grace is it prints white. We use it only a handful of times each...
Greetings,
I haven't been able to find any information on this issue, hoping somebody has some info. I am trying to tile a large plot that is wider than the plotter.
What's happening is that the border of the tile isn't cut, so the shape can't be peeled.
To explain another way, say you wanted...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.