• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Summa F1612 Air Compressor

mbarden

mbarden

New Member
Hi Folks,
We've purchased a Summa F1612 and are getting the area ready for installtion. What air compressors have you installed? Do you get a sperate compressor or run air off of an existing paint booth complressor?
Thanks
 
PHILJOHNSON

PHILJOHNSON

Sales Manager
Good afternoon,

The air compressor that you select will vary depending on whether you are getting any of the pneumatic tools like the POT or high frequency router, but if you aren't getting any of the pneumatic tools a "pancake" compressor will be sufficient for the media advance clamps. If you are getting some of the pneumatic tools, a lot of the companies that we work with like to use the California Air Tools compressors and the reviews have been solid on those. Not sure who you purchased the 1612 from, but we usually send out a full site preparation guide ahead of time that lists out all the specs for the compressor, electrical, etc. so you might check with your dealer to see if they have anything like that.

Best regards,

Phil Johnson
Airmark Corporation
(800)527-7778, ext. 112
philj@airmark.com
 
N

netsol

Active Member
no reason you can't do either, as long as it is good, clean DRY air
look in the installation manual and bebsure you give it thevpressure it requires
 
mbarden

mbarden

New Member
PHILJOHNSON said:
Good afternoon,

The air compressor that you select will vary depending on whether you are getting any of the pneumatic tools like the POT or high frequency router, but if you aren't getting any of the pneumatic tools a "pancake" compressor will be sufficient for the media advance clamps. If you are getting some of the pneumatic tools, a lot of the companies that we work with like to use the California Air Tools compressors and the reviews have been solid on those. Not sure who you purchased the 1612 from, but we usually send out a full site preparation guide ahead of time that lists out all the specs for the compressor, electrical, etc. so you might check with your dealer to see if they have anything like that.

Best regards,

Phil Johnson
Airmark Corporation
(800)527-7778, ext. 112
philj@airmark.com
Click to expand...
We got the Summa from Northlight Color. they sent the guide but honestly its a little confusing. As with anything you can spend a lot of money on the ancillary products so I'm wondering if anyone has any good suggestions. We do not have a pneumatic tools ordered. we do have the 1.4 router though.
 
PHILJOHNSON

PHILJOHNSON

Sales Manager
There are several guides, and some companies make their own, so it's possible the one you received is quite a bit different than the one we created(which we started when we owned and operated Summa and then refined it over time). If you aren't getting any pneumatic tools, there is no need at all to invest in a high capacity compressor when all you'll be using the air for is the pneumatic clamps. 100 PSI(7 bar) @ 0.7CFM is all you need for the clamps.

Best regards,

Phil Johnson
Airmark Corporation
(800)527-7778, ext. 112
philj@airmark.com
 
ProColorGraphics

ProColorGraphics

New Member
mbarden said:
We got the Summa from Northlight Color. they sent the guide but honestly its a little confusing. As with anything you can spend a lot of money on the ancillary products so I'm wondering if anyone has any good suggestions. We do not have a pneumatic tools ordered. we do have the 1.4 router though.
Click to expand...
It doesn't take much. My building has a big compressor setup as it was an old forklift service building. But when that went out for a while, I just used a small pancake compressor for a few weeks and it worked just fine. I would get a decent sized tank and a super quiet one if it's gonna be in the same area.
 
K

kosh_al

New Member
PHILJOHNSON said:
Good afternoon,

The air compressor that you select will vary depending on whether you are getting any of the pneumatic tools like the POT or high frequency router, but if you aren't getting any of the pneumatic tools a "pancake" compressor will be sufficient for the media advance clamps. If you are getting some of the pneumatic tools, a lot of the companies that we work with like to use the California Air Tools compressors and the reviews have been solid on those. Not sure who you purchased the 1612 from, but we usually send out a full site preparation guide ahead of time that lists out all the specs for the compressor, electrical, etc. so you might check with your dealer to see if they have anything like that.

Best regards,

Phil Johnson
Airmark Corporation
(800)527-7778, ext. 112
philj@airmark.com
Click to expand...
Phil, from what I read in the Summa F Series User Manual Rev15 (page 1-19, section 1.5.6), the HF router appears to still be an electric motor (like the standard router) with a pneumatic "clamp" for the collet for the bit. I imagine since it is just the collet using the air pressure, that a large capacity compressor is not needed for the HF router. We are going to get our F1612 up and running hopefully in the next two weeks and we shall find out!! We purchased this compressor to use and we have the EOT, not the POT. FORTRESS 2 Gallon, 135 PSI Ultra Quiet Oil-Free Hand-Carry Jobsite Air Compressor
 
Last edited:
balstestrat

balstestrat

Problem Solver
kosh_al said:
Phil, from what I read in the Summa F Series User Manual Rev15 (page 1-19, section 1.5.6), the HF router appears to still be an electric motor with a pneumatic "clamp" for the collet for the bit. I imagine since it is just the collet using the air pressure, that a large capacity compressor is not needed for the HF router. We are going to get our F1612 up and running hopefully in the next two weeks and we shall find out!! We purchased this compressor to use and we have the EOT, not the POT. FORTRESS 2 Gallon, 135 PSI Ultra Quiet Oil-Free Hand-Carry Jobsite Air Compressor
Click to expand...
You need dry air (air dryer) for the POT and HF router. That's why you need to go up with the compressor.

 
You must log in or register to reply here.
Top