Search results

If it is using EPSON firmware you will need the adjustment program which EPSON supplies to us service centers.....there are bootleg copies on ebay The pump cap assy is around $275 if you want to be proactive and replace, they do wear out, unlike many of the other parts that may come up as to be...

That part that you are referring to is the heater.....I am am Epson tech and have removed that part to get it through doors. There are a several screws around the perimeter that hold that cover on, the cover also has the heating elements strung under it. Once the screws are removed, lift up and...

Absolutely, I start with the one that has had the most recent issues: Dropped/Deflected nozzles, etc., then the oldest one, or I just start with the left out of habit it the other two factors do not apply

As an Epson tech, I see a lot of people swapping out the Main Formatter Board on Epson printers with the 1A39 print head Error. There is a small fuse on the board that can cause error as discussed first in the service manual, which is misleading. While I have done hundreds of heads I have seen...

I'm an authorized Epson Tech. That is most likely one of the print heads causing that. Have you seen any 1A39 Print Head Errors? One way to figure out if that is the issue when it becomes more consistent would be to put it in single head mode and see if you can isolate it to a specific head...

Howdy......did you get this resolved? I am working on one now with the same error....have replaced Sub Board E (heater control board) and verified continuity in the thermistors. I am going to move onto the main board next.

There is also a paper feed encoder disc on the inside left cover that you may be able to reach from the inside....that disc is like a MAP for the paper feed platen and if there is dust on it it may under or overfeed causing banding....Also, check the belt to make sure it is not too loose (or...

I can get Epson parts, sent you a text Rob Cota "Canon, Epson, HP & Epson Factory Trained and Authorized Technician" "CompTIA PDI +, Printing & Document Imaging Certified Professional" WeFixPrinters.com 2901 182nd St. Redondo Beach, CA 90278 310-937-4588 Tel 310-941-5748 Cel...

I suppose the print head could be faulty. If you print a standard nozzle test, it can look normal. Some of the advanced, manual head alignment patterns will can show defects in the heads that standard patterns may not show. That is the issue with some of these printers using Epson heads, many...

there is a menu in the control panel that allow to print on one head, it is called head mode.....shouldn't be too hard to find. It's in one of the top setup menus, or it will be in the users manual, I am in the field and cannot look up now

You may need a printhead if the missing nozzles are consistent and especially if there is nozzle deflection around it That may be a European Model so I may not be able to get parts for it....if you send the serial number I can verify origin

It isn't the most difficult part to replace.....you need to remove the top right cover, control panel and side right covers....I can get you the pages from the manual I can also get the part for you...it is $227 Where are you located?

A weak pump cap can cause this as the pump cap is responsible for getting the head primed up to print ........I would replace those. You mentioned the heads, dampers etc were replaced already?

I would make sure the Auto Clean feature is turned off. Some printers have an option as to how many cleanings to run if clogged nozzles are detected example 1-5 ....There may also be a driver setting where this is located for each job. If that doesn't do it, I might do a firmware upgrade.

you might want to replace the pump cap, it may not be properly priming the magenta line......try another magenta ink if you have one and you may then have a head issue I can get parts if you need them

There is some serious nozzle deflection that points to a faulty head, I would definatley try to clean the face of the head and pour some solution on the caps and let soak and then run cleaning, but the head is likely going to have to be replaced.....I am an authorized Epson tech and can help you...

It is definately one of the heads, I am an authorized tech and have done many of these....I have seen that error caused by a fuser on the old GS6000. These fuses are are user replaceable anyways, they are micro soldered on the main boards. Is this printer under warranty? Is Decision One...

The dampers are housed in the duct assy which plugs into the top of the head, they can clog up and cause issues. The ink is under high pressure so you need to run the inner tube reduction procedure from the adjustment program before disconnecting the ink tubes from the duct assy. This pressure...

Authorized Large Format Epson Stylus Pro Technician Based in Los Angeles available for tech support or on-site repair services in and out of the state. Also can get Genuine Epson parts, including printhead, dampers, pump caps, main board etc WeFixPrinters.com, 310-941-5748, info@wefixprinters.com

Image Authentics is correct, always check medis first, most tech's have very little printing experience and do not see the odd paper issues that users see like this