• I want to thank all the members that have upgraded your accounts. I truly appreciate your support of the site monetarily. Supporting the site keeps this site up and running as a lot of work daily goes on behind the scenes. Click to Support Signs101 ...

Search results

  1. How do you Cost you Gerber Work?

    Gerber pricing built in...very inexpensive also. http://graphixcalc.com/html/xl.html

  3. Master Cutter Won't Cut. Grrrrr

    Look underneath the control panel(front & back of plotter). there should be some screws...well there on my Tiger1000 anyway.

  4. Firefox 3

    Man, where has this been all my life? I just downloaded it & Wow! FAST! Thanks for the Thread guys. I think I may just start using this instead of IEX. Takes some getting used to tho, but I will adapt.

  5. Quickbooks invoice to PDF? How?

    www.pdf995.com print .pdf out of any software.

  6. transfer right

    Check with Fellers 800-654-8405, you might be next day from one of their locations

  7. RTA, I need to sub this out!

    http://www.thesignexpert.com/TheSignExpert.com/Sign_Business_Free_RTA_Vinyl_Price_Calculator.html

  8. Weeding Small Text (Oracal 651)

    I agree with going into the ice box. I left mine in overnite. Work small sections at a time as the vinyl will start to warm up & become more difficult

  9. Installation Rate for Routed Letters

    I am the same, by the hour + supplies(drill bits adhesive etc.). Drive time to & from site also.

  10. New Member with invoice software question

    I use both Quickbooks & GraphixCALC(merchant member scroll down)
  11.

    Max. Cutting area, CE-5000-60

    On a 24" roll I try to limit the max width to 23", more like 22.5" in most cases.

  12. Graphtec Tangetial emmulation

    I recently did some very small letters with my CE5000-60. The trick for me was to slooow down the speed.

  13. New guy looking to buy a plotter

    Take a look at the link below. Lots of good info there. www.thesignexpert.com

  14. Getting Started

    File dropdown, save as, .eps, then import to SignGo & cut from there.

  15. Free professional grade font each month

    Thx Doc.

  16. Ce 3000-60 or Qe-60

    I am looking at a Graphtec Ce 3000-60 & also a Vinyl Express Qe-60. Any thoughts on these as to which would be the better product? Are they very different? I would like to cut out of Graphix Advantage 6.21 & want to know if I could use the FC2100-60A Driver? Thanks for any input you may have.

  17. What sells the most ?

    A good starting place would be to join your local Home Builders Association. Those guys usually need Mags, Vehicle Lettering, Coro Signs, Site Signs etc.. Pick up GraphixCALC software(scroll down to bottom of page) to keep your pricing consistent & where you need to be. Also don't think that all...

  18. Thoughts on...Colorspan 72 UVR

    my last employer had the colorspan flatbed. It ran constantly 8hrs a day Mon-Fri, parked Sat & Sun. The only real thing was if printing a 4'x8' full bleed the operator would have to use a "trailer" at the end (6"-8" x width of same material). Hope this helps some.

  19. Graphix Advantage 6.2 to Master tiger 1000 plotter

    The GA I have was running a Graphtec plotter. The issue is that when I go to my list of plotters to install there are no Master Plotters available. I tried a few of the other 24" options in the list but when I cut I get garbage. I am looking for a way to get the driver from the SignGo software...

  20. Graphix Advantage 6.2 to Master tiger 1000 plotter

    Just picked up a Master Tiger 1000 plotter. Would like to run it using GA, but not sure if there is a way to install this as a plotter. It came with SignGo software which will run the plotter. Any way to get this to work with GA or will I have to export each job as an .eps over to Sign Go? Thanks
View older results
Top